VS-ST230C Datasheet, PDF (2/9 Pages) Vishay Siliconix – Phase Control Thyristors

www.vishay.com
VS-ST230C Series
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
Maximum average on-state current
at heatsink temperature
I_T(AV)
Maximum RMS on-state current
I_T(RMS)
Maximum peak, one-cycle
non-repetitive surge current
I_TSM
Maximum I²t for fusing
I²t
Maximum I²ïƒ–t for fusing
Low level value of threshold voltage
High level value of threshold voltage
Low level value of on-state slope resistance
High level value of on-state slope resistance
Maximum on-state voltage
Maximum holding current
Maximum (typical) latching current
I²ïƒ–t
V_T(TO)1
V_T(TO)2
r_t1
r_t2
V_TM
I_H
I_L
TEST CONDITIONS
180° conduction, half sine wave
double side (single side) cooled
DC at 25 °C heatsink temperature double side cooled
t = 10 ms
t = 8.3 ms
No voltage
reapplied
t = 10 ms
t = 8.3 ms
t = 10 ms
t = 8.3 ms
100 % V_{RRM ï€} 
reapplied
No voltage
reapplied
Sinusoidal half wave,
initial T_J = T_J maximum
t = 10 ms
t = 8.3 ms
100 % V_{RRM ï€} 
reapplied
t = 0.1 to 10 ms, no voltage reapplied
(16.7 % x  x I_T(AV) < I <  x I_T(AV)), T_J = T_J maximum
(I >  x I_T(AV)), T_J = T_J maximum
(16.7 % x  x I_T(AV) < I <  x I_T(AV)), T_J = T_J maximum
(I >  x I_T(AV)), T_J = T_J maximum
I_pk = 880 A, T_J = T_J maximum, t_p = 10 ms sine pulse
T_J = 25 °C, anode supply 12 V resistive load
VALUES UNITS
410 (165)
A
55 (85)
°C
780
5700
5970
A
4800
5000
163
148
kA²s
115
105
1630
kA²ïƒ–s
0.92
V
0.98
0.88
m
0.81
1.69
V
600
mA
1000 (300)
SWITCHING
PARAMETER
Maximum non-repetitive rate of rise
of turned-on current
Typical delay time
Typical turn-off time
SYMBOL
dI/dt
t_d
t_q
TEST CONDITIONS
Gate drive 20 V, 20 , t_r  1 μs
T_J = T_J maximum, anode voltage  80 % V_DRM
Gate current 1 A, dI_g/dt = 1 A/μs
V_d = 0.67 % V_DRM, T_J = 25 °C
I_TM = 300 A, T_J = T_J maximum, dI/dt = 20 A/μs, 
V_R = 50 V, dV/dt = 20 V/μs, gate 0 V 100 , t_p = 500 μs
VALUES
1000
1.0
100
UNITS
A/μs
μs
BLOCKING
PARAMETER
Maximum critical rate of rise
of off-state voltage
Maximum peak reverse and 
off-state leakage current
SYMBOL
dV/dt
I_RRM,
I_DRM
TEST CONDITIONS
T_J = T_J maximum linear to 80 % rated V_DRM
T_J = T_J maximum, rated V_DRM/V_RRM applied
VALUES
500
UNITS
V/μs
30
mA
Revision: 16-Dec-13
2
Document Number: 94398
For technical questions within your region: [e-mail], [e-mail], [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000