VS-70TPS12PBF_15 Datasheet, PDF (2/9 Pages) Vishay Siliconix – Thyristor High Voltage, Phase Control SCR

VS-70TPS12PbF, VS-70TPS16PbF High Voltage Series
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
Maximum average on-state current
Maximum continuous RMS on-state
current as AC switch
I_T(AV)
I_T(RMS)
Maximum peak, one-cycle
non-repetitive surge current
I_TSM
Maximum I²t for fusing
I²t
Maximum I²âˆšt for fusing
Low level value of threshold voltage
High level value of threshold voltage
Low level value of on-state slope resistance
High level value of on-state slope resistance
Maximum peak on-state voltage
Maximum rate of rise of turned-on current
Maximum holding current
Maximum latching current
I²âˆšt
V_T(TO)1
V_T(TO)2
r_t1
r_t2
V_TM
dI/dt
I_H
I_L
Maximum reverse and direct leakage current I_RRM/I_DRM
Maximum rate of rise of off-state voltage
dV/dt
TEST CONDITIONS
T_C = 82 °C, 180° conduction half sine wave
VALUES UNITS
70
Lead current limitation
75
10 ms sine pulse, rated V_RRM applied
10 ms sine pulse, no voltage reapplied
10 ms sine pulse, rated V_RRM applied
10 ms sine pulse, no voltage reapplied
t = 0.1 ms to 10 ms, no voltage reapplied
Initial T_J = T_J
maximum
T_J = 125 °C
100 A, T_J = 25 °C
T_J = 25 °C
Anode supply = 6 V, resistive load, initial I_T = 1 A, T_J = 25 °C
Anode supply = 6 V, resistive load, T_J = 25 °C
T_J = 25 °C
T_J = 125 °C
T_J = 125 °C
V_R = Rated V_RRM/V_DRM
(T_J = T_J max., linear to 80 %
V_DRM = R_g-k = Open)
930
1100
4325
6115
61 150
0.916
1.21
4.138
3.43
1.4
150
200
400
1.0
15
500
A
A²s
A²âˆšs
V
mΩ
V
A/μs
mA
V/μs
TRIGGERING
PARAMETER
Maximum peak gate power
Maximum average gate power
Maximum peak gate current
Maximum peak negative gate voltage
SYMBOL
P_GM
P_G(AV)
I_GM
- V_GM
Maximum required DC gate voltage to trigger V_GT
Maximum required DC gate current to trigger I_GT
Maximum DC gate voltage not to trigger
V_GD
Maximum DC gate current not to trigger
I_GD
T = 30 μs
TEST CONDITIONS
T_J = - 40 °C
T_J = 25 °C
T_J = 125 °C
T_J = - 40 °C
T_J = 25 °C
T_J = 125 °C
Anode supply = 6 V resistive load
Anode supply = 6 V resistive load
T_J = 125 °C, V_DRM = Rated value
VALUES UNITS
10
W
2.5
2.5
A
10
1.8
V
1.5
1.1
150
100
mA
80
0.25
V
6
mA
Revision: 15-Apr-14
2
Document Number: 94391
For technical questions within your region: [e-mail], [e-mail], [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000