TIP-4131SCE-1 Datasheet, PDF (2/7 Pages) Vishay Siliconix – 12.1” Infrared Touch Panel

TIP-4131SCE-1
Vishay Dale
GENERAL DESCRIPTION
Vishay Dale Electronics TIP products are infrared touch panels
designed to fit most flat panel display technologies. The touch
panels consist of infrared emitters and detectors, scanning
electronics, a microprocessor based controller, a bezel and
optical filter assembly, and hardware to mount the touch panel
assembly to the flat panel display.
These touch panels are ideal for many applications including
medical instrumentation, machine or process controllers, point
of sale devices, public information displays, banking terminals,
and military.
Each panel has infrared LED emitters and phototransistors
along the X and Y axes, forming a grid of infrared light beams
across the face of the display. The first two numbers of the
TIP “matrix” number specify the number of X axis (vertical)
beams, and the last two numbers specify the number of Y
(horizontal) beams. The controller scans the emitter/detector
pairs one at a time and determines whether both X and Y
beams are blocked, indicating that a finger or stylus is present.
(When beams are blocked on only one axis, they are ignored
and not reported.) The controller determines the coordinates
of the touch point and reports it to the host computer. By
interpolating, a “virtual” beam between two physical beams,
the number of touch points on each axis is effectively doubled.
When an odd number of beams along either axis is blocked,
the coordinate of the center physical beam is reported. When
an even number of beams is blocked, the coordinate of the
virtual beam in the center of the blocked beams is calculated
and reported.
Vishay Dale’s TIP touch panels have a unique patented
scanning and logic system that make them virtually immune
to most lighting environments.
The touch controller supports ENTER, EXIT, CONTINUOUS,
and TRACKING report modes or combinations of these modes.
The controller also has a beeper output. Hardware
handshaking, software handshaking, baud rates, and X, Y
coordinate invert features are jumper selected. The user
initializes the desired report modes, coordinates are reported
automatically or upon request as needed. Several optical filters
are standard to provide the most cost effective filter for each
application. “Non-standard” filters may be specified as well.
The filter increases the contrast ratio of the display and protects
the display face and electronics. Vishay Dale can assist in
recommending the optimum filter based on years of experience
as a display manufacturer. The perimeter of the filter is bonded
to the bezel, and a bezel to front panel gasket is included to
provide a splash proof seal.
Optional PC based software provides simple touch panel
integration (see ordering instructions).
T5Driver emulates a mouse in Windows 95/98 applications.
TWDriver emulates a mouse in Windows applications.
TBDriver emulates a mouse in DOS applications.
Generic drivers or drivers for other operating systems are
available through Touch Base, Ltd. Contact Vishay Dale for
information.
(Windows is a registered trademark of the Microsoft Corporation.)
PIN CONNECTIONS
J1 DATA CONNECTOR
TOUCH PANEL CONNECTOR
10-PIN (db-9)
PIN PIN DESCRIPTION
1
1 N/C (reserved)
2
6 N/C (reserved)
3
2 TxD (output)
4
7 CTS (input)
5
3 RxD (input)
6
8 RTS (output)
7
4 DSR (input)
8
9 N/C (reserved)
9
5 Ground
10
- N/C (reserved)
HOST CONNECTOR
(db-9) (db-25)
PIN PIN DESCRIPTION
2
3 RxD
7
4 RTS
3
2 TxD
8
5 CTS
4
20 DTR
5
7 GND
To make a serial communication cable, use insulation
displacement connectors (IDC). Press a 10-pin IDC connector
onto one end of the ribbon cable, press a db-9 connector onto
the other end. Match pin 1 of the 10-pin to pin 1 of the db-9, the
10^thpin is not used on the db-9.
The busy indicator from the host may be changed from CTS to
DSR by changing the position of the jumper at W3.
MATING CONNECTORS
J1
J2,J3
J4
J5
VISHAY
280105-02
280105-04
280108-06
280108-05
OTHER
AMP 746285-1
AMP 746285-4
MOLEX 22-01-3037 housing
08-50-0114 terminals
AMP 1-480424-0 housing
350689-1 socket terminals
J4 AUDIO FEED BACK CONNECTOR (BEEPER)
PIN DESCRIPTION
1 Ground
2 Beeper Signal (active low)
3 Beeper Power Output (+ 5 VDC)
J5 POWER CONNECTOR
PIN DESCRIPTION
1 N/C
2 Ground
3 Ground
4 + 5V
W1 JUMPERS
BAUD RATE (Select 1)
19200 Baud
9600 Baud
SOFTWARE HANDSHAKING
NORMAL X
NORMAL Y
www.vishay.com
2
Document Number: 37070
Revision 28-Jun-01