TCET2600_07 Datasheet, PDF (2/9 Pages) Vishay Siliconix – Optocoupler, Phototransistor Output, AC Input (Dual, Quad Channel)

TCET2600/TCET4600
Vishay Semiconductors ^{Optocoupler, Phototransistor Output,}
AC Input (Dual, Quad Channel)
ABSOLUTE MAXIMUM RATINGS ⁽¹⁾
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
INPUT
Reverse voltage
Forward current
Forward surge current
Power dissipation
Junction temperature
OUTPUT
t_p ≤ 10 µs
V_R
6
V
I_F
± 60
mA
I_FSM
± 1.5
A
P_diss
100
mW
T_j
125
°C
Collector emitter voltage
V_CEO
70
V
Emitter collector voltage
V_ECO
7
V
Collector current
I_C
50
mA
Collector peak current
t_p/T = 0.5, t_p ≤ 10 ms
I_CM
100
mA
Power dissipation
P_diss
150
mW
Junction temperature
T_j
125
°C
COUPLER
Isolation test voltage (RMS)
Total power dissipation
Operating ambient temperature range
Storage temperature range
Soldering temperature ⁽²⁾
t = 1 min
2 mm from case, t ≤ 10 s
V_ISO
P_tot
T_amb
T_stg
T_sld
5000
250
- 40 to + 100
- 55 to + 125
260
V_RMS
mW
°C
°C
°C
Notes
(1) _{Tamb = 25 °C, unless otherwise specified.}
Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum
Rating for extended periods of the time can adversely affect reliability.
(2) _{Refer to wave profile for soldering conditions for through hole devices.}
ELECTRICAL CHARACTERISTCS
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
INPUT
Forward voltage
I_F = ± 50 mA
V_F
1.25
1.6
V
Junction capacitance
V_R = 0 V, f = 1 MHz
C_j
50
pF
OUTPUT
Collector emitter voltage
I_C = 100 µA
V_CEO
70
V
Emitter collector voltage
Collector dark current
I_E = 100 µA
V_ECO
7
V_CE = 20 V, I_F = 0 A,
E=0
I_CEO
V
100
nA
COUPLER
Collector emitter saturation voltage
Cut-off frequency
Coupling capacitance
I_F = 10 mA, I_C = 1 mA
V_CE = 5 V, I_F = 10 mA,
R_L = 100 Ω
f = 1 MHz
V_CEsat
f_c
C_k
0.3
V
100
kHz
0.3
pF
Note
T_amb = 25 °C, unless otherwise specified.
Minimum and maximum values were tested requierements. Typical values are characteristics of the device and are the result of engineering
evaluations. Typical values are for information only and are not part of the testing requirements.
CURRENT TRANSFER RATIO
PARAMETER
TEST CONDITION
I_C/I_F
V_CE = 5 V, I_F = ± 5 mA
SYMBOL
CTR
MIN.
20
TYP.
MAX.
300
UNIT
%
www.vishay.com
2
For technical questions, contact: [e-mail]
Document Number: 83726
Rev. 1.5, 07-Dec-07