SI4720CY Datasheet, PDF (2/8 Pages) Vishay Siliconix – Battery Disconnect Switch

Si4720CY
Vishay Siliconix
ABSOLUTE MAXIMUM RATINGS
Voltage Referenced to GND
V_S, V_Da . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 32 V
V_SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 30 V
V_IN1, V_IN2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 15 V
V_GS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V
Storage Temperature . . . . . . . . . . . . . . . . . . . –55 to 150_C
Power Dissipation^b (t = 10 sec) . . . . . . . . . . . . . . . . 2.5 W
(t = steady state) . . . . . . . . . . . 1.5 W
Notes
a. V_SD ≤ 30 V_DC
b. Device mounted with all leads soldered to 1” x 1” FR4 with laminated
copper PC board.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING RANGE
V_S, V_D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V to 30 V
V_IN1, V_IN2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 13.2 V
I_DS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 A to 6 A
Operating Temperature Range . . . . . . . . . . . . –25 to 85_C
Junction Temperature . . . . . . . . . . . . . . . . . . . –25 to 150_C
SPECIFICATIONS
Parameter
Symbol
Test Conditions
Unless Otherwise Specified
Limits
Temp^a Min^b Typ^c
Max^b
Unit
On-Resistance
Leakage Current
Supply Current
Input Voltage Low
Input Voltage High
Input Leakage Current
Turn-On Delay
Turn-Off Delay
IN
to D or S
Break-Before-Make^d
Rise Time
Fall Time
Voltage Across Pin 6 and 7
Forward Diode
r_DS
I_DS(off)
I_S(off)
I_S(on)
V_INL
V_INH
I_INH
t_ON(IN)
t_OFF(IN)
t_BBM
t_RISE
t_FALL
V_GS
V_SD
V_S = 10 V, I_D = 1 A, V_IN = H
V_DS = 10 V
V_S = 21 V
V_S = 10 V and V_S = 21 V
V_IN = 5.0 V
V_S = 10 V, R_L = 5 W , Figure 1
V_S = 10 V, R_L = 5 W , Figure 1
V_S = 30 V
I_D = –1 A
Room
0.0155
0.020
W
Room
1
Room
1
mA
Room
1.1
6
Full
Full
2.5
1
V
Full
5
mA
Room
2.2
2.9
10
Room
Room
1.5
2.1
ms
1.05
Room
1.3
2.5
Room
50
100
ns
Room
Room
10.2
18
V
1.1
Notes
a. Room = 25_C, Full = as determined by the operating temperature suffix.
b. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. Guaranteed by design, not subject to production testing.
www.vishay.com S FaxBack 408-970-5600
2-2
Document Number: 70664
S-49524—Rev. B, 21-Jul-97