CS206 Datasheet, PDF (2/2 Pages) Vishay Siliconix – Resistor/Capacitor Networks ECL Terminators and Line Terminator, Conformal Coated, SIP

Res/CapNetworks, ECL Terminators and Line Terminator
CS206
Vishay Dale
DIMENSIONS in inches [millimeters]
L
Max.
0.050 [1.27] Typ.
0.085 [2.160] Typ.
0.135 [3.43] Max.
0.020
[0.508]
0.100 ± 0.005 [2.54 ± 0.127]
Non-Cumulative
at Point of Egress
H
Max.
0.050 [1.27]
Pin #1 is extreme left-hand terminal on side with marking.
CL
Seating Plane
0.010
for 0.040 [1.016] Ø Hole
[0.254]
0.007 [0.178]
0.135 + 0.015 - 0.010
Ref.
[3.43 + 0.381 - 0.254]
H (Height) Maximum:
B = 0.250" [6.35] (Circuit E and M)
C = 0.350" [8.89] (Circuit T)
E = 0.325" [8.26] (Circuit A)
NUMBER
OF PINS
4 pin
5 pin
6 pin
7 pin
8 pin
9 pin
10 pin
11 pin
12 pin
13 pin
14 pin
15 pin
16 pin
17 pin
18 pin
L
MAXIMUM
0.400 [10.16]
0.500 [12.70]
0.600 [15.24]
0.700 [17.78]
0.800 [20.32]
0.900 [22.86]
1.000 [25.40]
1.100 [27.94]
1.200 [30.48]
1.300 [33.02]
1.400 [35.56]
1.500 [38.10]
1.600 [40.64]
1.700 [43.18]
1.800 [45.72]
150
MATERIAL SPECIFICATIONS
Flammability:
UL 94V-0.
100
Lead Material:
Phosphorus-bronze, solder plated.
Body Material:
Epoxy coated.
50
Solderability:
Per MIL-STD-202, Method 208E.
Part Marking:
0
0
25
50
75
100
125
150
Derating
70
Moisture Resistance:
Ambient Temperature °C
Pin #1 identification, part number
(abbreviated as space allows),
DALE^® or D, date code
Meets requirements of MIL-STD-
202, Method 106.
PERFORMANCE
TEST
CONDITION
MAX. ∆R
(Typical Test Lots)
Thermal Shock
Subject to 5 cycles from - 65°C to + 125°C.
Short Time Overload
2.5 x rated working voltage for 5 seconds at + 25°C.
Moisture Resistance
Cycle from + 25°C to + 65°C to + 25°C over 8 hours at 90 - 98% relative humidity,
with 10% of rated power applied, for 20 cycles. Stop cycling after an even number
of cycles and stabilize networks at high humidity for 1 to 4 hours. Condition
networks at -10°C for 3 hours, then return to temperature cycling. On completion of
cycling condition networks at + 25°C at 50% r.h. for 22 to 24 hours.
Resistance to Soldering Heat _{Immerse pins in melted solder to the lead standoffs at + 350°C for 3 seconds max.}
Mechanical Shock
18 shocks of 100 G and 6 ms.
± 0.5% ∆R
± 0.25% ∆R
± 0.5% ∆R
± 0.25% ∆R
± 0.25% ∆R
Vibration
12 cycles varied logarithmically from 10Hz to 2000Hz to 10Hz over 20 minutes.
± 0.25% ∆R
Load Life
Resistance to Solvents
1000 hours at + 70°C, rated power applied 1.5 hours “ON, 0.5 hour “OFF”.
± 1.0% ∆R
Immerse and scrub samples with isopropyl alcohol, trichlorethylene and Freon TMC. ^{Marking remains legible}
Solderability
Immerse leads in 60/40 tin-lead solder using R flux at + 245°C for 5 seconds
maximum.
Minimum 95% solder
coverage
Terminal Strength
Withstand 2.2 kg pull 1 minute.
± 0.25% ∆R
Case Insulation Resistance _{100 V applied between case and terminals tied together.}
IR = 10,000 Megohm
minimum
Document Number: 31519
Revision 10-Sep-04
For Technical Questions, contact: [e-mail]
www.vishay.com
61