CNY65EXI_15 Datasheet, PDF (2/7 Pages) Vishay Siliconix – Optocoupler, Phototransistor Output, ATEX Certified

www.vishay.com
CNY65Exi
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (T_amb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
INPUT
Reverse voltage
Forward current
Forward surge current
Power dissipation
Junction temperature
OUTPUT
t_p ≤ 10 μs
V_R
5
V
I_F
75
mA
I_FSM
1.5
A
P_diss
120
mW
T_j
100
°C
Collector emitter voltage
Emitter collector voltage
Collector current
Collector peak current
Power dissipation
Junction temperature
COUPLER
V_CEO
32
V
V_ECO
7
V
I_C
50
mA
t_p/T = 0.5, t_p ≤ 10 ms
I_CM
100
mA
P_diss
130
mW
T_j
100
°C
DC isolation test voltage
Total power dissipation
Ambient temperature range
Storage temperature range
Soldering temperature
t = 1 min
V_ISO
11.6
kV
P_tot
250
mW
T_amb
-55 to +85
°C
T_stg
-55 to +100
°C
2 mm from case, t ≤ 10 s
T_sld
260
°C
Note
• Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
Maximum Rating for extended periods of the time can adversely affect reliability.
ELECTRICAL CHARACTERISTICS (T_amb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
INPUT
Forward voltage
OUTPUT
I_F = 50 mA
V_F
1.25
1.6
V
Collector emitter voltage
Emitter collector voltage
Collector dark current
COUPLER
DC isolation test voltage
Isolation resistance
I_C = 1 mA
V_CEO
32
I_E = 100 μA
V_ECO
7
V_CE = 20 V, I_f = 0, E = 0
I_CEO
V
V
200
nA
t = 1 min
V_ISO ⁽¹⁾
11.6
kV
V_IO = 1 kV,
40 % relative humidity
R_IO ⁽¹⁾
10¹²
Ω
Collector saturation voltage
I_F = 10 mA, I_C = 1 mA
V_CEsat
0.3
V
Cut-off frequency
V_CE = 5 V, I_F = 10 mA,
R_L = 100 Ω
f_c
110
kHz
Coupling capacitance
f = 1 MHz
C_k
0.3
pF
Notes
• Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
(1) _{Related to standard climate 23/50 DIN 50014.}
CURRENT TRANSFER RATIO (T_amb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
PART SYMBOL
CNY65Exi CTR
I_C/I_F
V_CE = 5 V, I_F = 10 mA
CNY65BExi CTR
MIN.
50
100
TYP.
100
MAX.
300
200
UNIT
%
%
Rev. 2.5, 10-Feb-15
2
Document Number: 83541
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000