595D107X9016D2T Datasheet, PDF (17/24 Pages) Vishay Siliconix – Solid Tantalum Chip Capacitors TANTAMOUNT, Conformal Coated, Maximum CV

www.vishay.com
Conformal Coated Guide
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
T₂
(max.)
0.024
[0.600]
max.
B₁ (max.) ⁽⁶⁾
For tape feeder
reference only
including draft.
Concentric around B₀
Deformation
between
embossments
0.157 ± 0.004
[4.0 ± 0.10]
10 pitches cumulative
tolerance on tape
0.059 + 0.004 - 0.0
± 0.008 [0.200]
[1.5 + 0.10 - 0.0]
Embossment
0.079 ± 0.002
0.069 ± 0.004
[2.0 ± 0.05]
[1.75 ± 0.10]
Top
cover
tape
K₀
Top
cover
tape
0.004 [0.10]
max.
Center lines
of cavity
A₀
B₀
P₁
USER DIRECTION
OF FEED
0.030 [0.75]
min. ⁽³⁾
FW
0.030 [0.75]
min. ⁽⁴⁾
20°
Maximum
component
rotation
(Side or front sectional view)
D₁ (min.) for components
0.079 x 0.047 [2.0 x 1.2] and
l.arger
(5)
Maximum
cavity size ⁽¹⁾
Cathode (-)
Anode (+)
DIRECTION OF FEED
R
min.
Bending radius ⁽²⁾
R minimum:
8 mm = 0.984" (25 mm)
12 mm and 16 mm = 1.181" (30 mm)
20° maximum
component rotation
Typical
component
cavity
B₀
center line
A₀
(Top view)
Typical
component
center line
3.937 [100.0]
0.039 [1.0]
max.
Tape
0.039 [1.0]
max.
0.9843 [250.0]
Camber
(Top view)
Allowable camber to be 0.039/3.937 [1/100]
Non-cumulative over 9.843 [250.0]
Tape and reel specifications: All case sizes are
available on plastic embossed tape per EIA-481.
Standard reel diameter is 7" (178 mm).
Lengthwise orientation at capacitors in tape
Cathode (-)
DIRECTION OF FEED
H-Case only
Anode (+)
Notes
• Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
(1) _{A0, B0, K0, are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body}
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A₀, B₀, K₀) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20°.
(2) _{Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide}
“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum.
(3) _{This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed}
cavities or to the edge of the cavity whichever is less.
(4) _{This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier}
tape between the embossed cavity or to the edge of the cavity whichever is less.
(5) _{The embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. Dimensions of}
embossement location shall be applied independent of each other.
(6) _{B1 dimension is a reference dimension tape feeder clearance only.}
Revision: 23-Jul-13
5
Document Number: 40150
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000