VJ0603A470JXAAT Datasheet, PDF (1/6 Pages) Vishay Siliconix – Surface Mount Multilayer Ceramic Chip Capacitors for Commercial Applications

VJ C0G (NP0) Dielectric
Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitors
for Commercial Applications
ELECTRICAL SPECIFICATIONS
Note:
Electrical characteristics at + 25 °C unless otherwise specified
Operating Temperature: - 55 °C to + 150 °C
Capacitance Range: 1.0 pF to 0.056 µF
Voltage Range: 10 Vdc to 1000 Vdc
Temperature Coefficient of Capacitance (TCC):
0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C
Dissipation Factor (DF):
0.1 % maximum at 1.0 V_rms and 1 kHz for values > 1000 pF
0.1 % maximum at 1.0 V_rms and 1 MHz for values ≤ 1000 pF
Aging Rate: 0 % maximum per decade
FEATURES
• C0G is an ultra-stable dielectric offering a
Temperature Coefficient of Capacitance (TCC)
of 0 ppm/°C ± 30 ppm/°C
• Low Dissipation Factor (DF)
• Surface mount, wet build process
• Reliable Noble Metal Electrode (NME) system
• Halogen-free according to IEC 61249-2-21
APPLICATIONS
• Timing and tuning circuits
• Sensor and scanner applications
• Snubber and surge suppression
Insulation Resistance (IR):
At + 25 °C and rated voltage 100 000 MΩ minimum or
1000 ΩF, whichever is less
At + 125 °C and rated voltage 10 000 MΩ minimum or
100 ΩF, whichever is less
Dielectric Strength Test:
Performed per Method 103 of EIA 198-2-E.
Applied test voltages:
≤ 500 Vdc-rated:
200 % of rated voltage
630 Vdc/1000 Vdc-rated: 150 % of rated voltage
ORDERING INFORMATION
VJ0805
CASE
CODE
A
DIELECTRIC
102
CAPACITANCE
NOMINAL CODE
K
CAPACITANCE
TOLERANCE
X
A
TERMINATION
DC VOLTAGE
RATING ⁽¹⁾
0402
0603
0805
1206
1210
1808
1812
1825
2220
2225
A = C0G (NP0)
Expressed in
picofarads (pF).
The first two
digits are
significant, the
third is a
multiplier. An
“R” indicates a
decimal point.
Examples:
102 = 1000 pF
1R8 = 1.8 pF
B = ± 0.10 pF X = Ni barrier
C = ± 0.25 pF 100 % tin plate
D = ± 0.5 pF matte finish
F=±1%
F = AgPd
G=±2%
B = Polymer
J = ± 5 % 100 % tin plate
K = ± 10 % matte finish ⁽⁵⁾
Note:
B, C, D < 10 pF
F, G, J, K ≥ 10 pF
X = 25 V
A = 50 V
B = 100 V
C = 200 V
E = 500 V
L = 630 V
G = 1000 V
A
MARKING
A = Unmarked
M = Marked
Note: Marking is
only available for
0805 and 1206
with termination
code ”X”
T
### ⁽²⁾⁽⁴⁾
PACKAGING ^PROCESS
CODE
T = 7" reel/plastic tape
C = 7" reel/paper tape
R = 11 1/4" reel/plastic tape
P = 11 1/4" reel/paper tape
O = 7" reel/flamed paper tape
I = 11 1/4"/13" reel/flamed paper tape
Note: “I” and “O” is used for
“F” termination paper taped
size 0402/0603/0805
Notes
(1) _{DC voltage rating should not be exceeded in application}
(2) _{Process Code may be added with up to three digits, used to control non-standard products and/or special requirements}
(3) _{Case size designator may be replaced by a four digit drawing number used to control non-standard products and/or requirements}
(4) _{“A2” temporarily used to identify manufacturing plant for size ≥ 1812}
(5) _{Selected values available, contact [e-mail] for list of released ratings}
www.vishay.com
38
For technical questions, contact: [e-mail]
Document Number: 45053
Revision: 23-Sep-09