RCG-E3 Datasheet, PDF (1/6 Pages) Vishay Siliconix – Green Thick Film Chip Resistors

www.vishay.com
RCG e3
Vishay Draloric
Green Thick Film Chip Resistors
FEATURES
• Green resistor - does not use RoHS exemptions
• Stability R/R = 1 % for 1000 h at 70 ° C
• 2 mm pitch packaging option for 0603 size
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
TYPE
CASE
CASE
SIZE
SIZE
IMPERIAL METRIC
POWER RATING
P₇₀
W
LIMITING
ELEMENT
VOLTAGE
U_max.
AC_RMS/DC
V
TEMPERATURE
COEFFICIENT
± ppm/K
TOLERANCE
±%
RESISTANCE
RANGE

SERIES
0.063
50
RCG0402 0402 RR1005M
100
150 to 10M
0.5, 1
E24; E96
150
1.0 to 147
200
5
1.0 to 10M
E24
RCG0603
0603
RR1608M
Zero-Ohm-Resistor: R_max. = 20 m, I_max. = 1.5 A
100
0.1
75
200
0.5, 1
5
1.0 to 10M
E24; E96
E24
RCG0805
0805
RR2012M
Zero-Ohm-Resistor: R_max. = 20 m, I_max. = 2.0 A
100
0.125
150
200
0.5, 1
5
1.0 to 10M
E24; E96
E24
RCG1206
1206
RR3216M
Zero-Ohm-Resistor: R_max. = 20 m, I_max. = 2.5 A
100
0.25
200
200
0.5, 1
5
1.0 to 10M
E24; E96
E24
Zero-Ohm-Resistor: R_max. = 20 m, I_max. = 3.5 A
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Marking: See datasheet “Surface Mount Resistor Marking” (document number 20020).
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
RCG0402
RCG0603
RCG0805
RCG1206
Rated dissipation P₇₀ ⁽¹⁾
Operating voltage U_max. AC_RMS/DC
Insulation voltage U_ins (1 min)
Insulation resistance
W
0.063
V
50
V
75

0.1
0.125
75
150
100
200
> 10⁹
0.25
200
300
Operating temperature range
°C
- 55 to + 155
Mass
mg
0.65
2
5.5
10
Note
(1) _{The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the}
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
Revision: 01-Sep-14
1
Document Number: 20047
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000