PHR Datasheet, PDF (1/6 Pages) Vishay Siliconix – ESCC ( ) 4001/023 Qualified High Precision (5 ppm, 0.01 %), Thin Film Chip Resistors

www.vishay.com
PHR
Vishay Sfernice
ESCC ( ) 4001/023 Qualified High Precision (5 ppm, 0.01 %),
Thin Film Chip Resistors
Vishay Sfernice Thin Film division holds ESCC QML
qualification (ESCC technology flow qualification).
These High-Rel. components are ideal for low noise and
precision applications, superior stability, low temperature
coefficient of resistance, and low voltage coefficient, Vishay
Sfernice’s precision thin film wraparound resistors exceed
requirements of MIL-PRF-55342G characteristics Y
(± 10 ppm/°C).
FEATURES
• Load life stability at ± 70 °C for 2000 h: 
0.15 % under Pn
• Low temperature coefficient down to ± 5 ppm/°C
• Very low noise (< -35 dB) and voltage coefficient
(< 0.01 ppm/V)
• Resistance range: 10  to 3 M (depending on size)
• Laser trimmed tolerances to ± 0.01 %
• TCR in lot tracking  5 ppm/°C
• Termination: Thin film technology
• SnPb terminations over nickel barrier
• ESCC 4001 (generic specifications)
• ESCC 4001/023 (detailed specifications)
• ESCC qualified
• SMD wraparound chip resistor
• Operating temperature range: -65 °C to +155 °C
• From 0402 to 2010
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
SIZE
ESCC
VARIANT
NUMBER
RESISTANCE
RANGE

RATED
POWER
AT + 70 °C
(Pn)
W ⁽¹⁾
LIMITING
ELEMENT
VOLTAGE
(UL)
V ⁽¹⁾
INSULATION
VOLTAGE
(U_i)
V
TOLERANCE
±%
TEMPERATURE
COEFFICIENT
± ppm/°C
PHR 0402
0402 13 and 14 10 to 150K
0.05
30
PHR 0603
0603 01 and 05 10 to 500K
0.1
35
50
0.01, 0.02, 0.05, 0.1
5, 10, 25
100
0.01, 0.02, 0.05, 0.1
5, 10, 25
PHR 0805
0805 02 and 06 10 to 750K
0.125
75
200
0.01, 0.02, 0.05, 0.1
5, 10, 25
PHR 1206
1206 03 and 07 10 to 3.5M
0.25
100
PHR 2010
2010 04 and 08 10 to 6M
0.50
150
300
0.01, 0.02, 0.05, 0.1
5, 10, 25
300
0.01, 0.02, 0.05, 0.1
5, 10, 25
Note
(1) _{Limiting voltages and power rating are already derated (for maximum ratings admissible, refer to P chip: www.vishay.com/cod?53017).}
CLIMATIC SPECIFICATIONS
Operating temperature
range
-65 °C; +155 °C
Soldering temperature
(T_sol)
260 °C, immersion 10 s
MECHANICAL SPECIFICATIONS
Substrate material Alumina
Technology
Thin Film
Film
Nickel Chromium with mineral 
passivation
Protection
Epoxy and silicone
Terminations
B type: SnPb over nickel barrier
for solder reflow ⁽³⁾
G type: Gold
Note
(2) _{For B terminations use recommended reflow profile #1 as per}
Application Note “Guidelines for Vishay Sfernice Resistive and
Inductive Components” (document number: 52029)
Revision: 28-Aug-15
1
Document Number: 53037
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000