NTCLP100E3103H Datasheet, PDF (1/6 Pages) Vishay Siliconix – NTC Thermistors, Special Long Lead Sensors

NTCLE400, NTCLS100, NTCLP100
Vishay BCcomponents
NTC Thermistors, Special Long Lead Sensors
FEATURES
• Accurate over wide temperature range
• High stability
• Excellent price/performance ratio
• High adhesive strength between PVC wire and
the encapsulating laquer
• Compliant to RoHS Directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
QUICK REFERENCE DATA
PARAMETER
Resistance value at 25 °C (R₂₅)
Tolerance on R₂₅-value ⁽²⁾
B_25/85-value
Tolerance on B_25/85-value
Operating temperature range:
VALUE
2.2K to 100K
±3
3977 to 4190
± 0.75 to ± 1.5
UNIT

%
K
%
At zero dissipation
(continuously)
- 40 to + 85
°C
At maximum dissipation
0 to + 55
Maximum power dissipation
at 55 °C
250
mW
Dissipation factor:
NTCLE400...
NTCLS100...
6.0
8.0
mW/K
NTCLP100...
Response time ⁽¹⁾:
NTCLE400...
NTCLS100...
NTCLP100...
6.0
7
 15
s
 10
Climatic category
(LCT/UCT/days)
40/085/56
Weight
NTCLE400...
NTCLS100...
4
6
g
NTCLP100...
6
Notes
(1) _{Response time in silicone oil MS 200/50. This is the time needed}
for the sensor to reach 63.2 % of the total temperature
difference when subjected to a temperature change from 25 °C
in air to 85 °C in oil.
(2) _{Tighter tolerances on R25 are available upon request.}
APPLICATIONS
Temperature measurement, sensing and control in remote
locations and for various environmental conditions.
DESCRIPTION
These sensors exist of a small NTC chip reflow soldered
between two AWG24 UL-2468 wires. They are lacquered
and insulated with black epoxy (NTCLE400 type), sleeved
(NTCLS100 type) or potted into a brass pipe (NTCLP100
type).
MARKING
UL mark on wire, no mark on body.
PACKAGING
The thermistors are packed in cardboard boxes; each box
containing 500 pieces.
DESIGN-IN SUPPORT
Other wire length and wire type (UL-2651 PVC 105 °C) are
available on request. The products can be provided with a
connector on request.
For complete curve computation, visit:
www.vishay.com/resistors-non-linear/curve-computation-list/
MOUNTING
By soldering or clamping the wire ends, in any position.
Body can be inserted or taped attached. Not intended for
fluid immersed applications.
ELECTRICAL DATA AND ORDERING INFORMATION
R₂₅
(k)
B_25/85-VALUE
SAP MATERIAL AND ORDERING NUMBER ⁽³⁾⁽⁴⁾
EPOXY
TYPE
SLEEVED
TYPE
PIPE
TYPE
OLD 12NC CODE 2381 641 .....
EPOXY-COATED SLEEVED BRASS-PIPE
TYPE
TYPE
TYPE
2.2 3977K ± 0.75 % NTCLE400E3222H NTCLS100E3222H NTCLP100E3222H
26222
36222
46222
4.7 3977K ± 0.75 % NTCLE400E3472H NTCLS100E3472H NTCLP100E3472H
26472
36472
46472
5 3977K ± 0.75 % NTCLE400E3502H NTCLS100E3502H NTCLP100E3502H
26502
36502
46502
10 3977K ± 0.75 % NTCLE400E3103H NTCLS100E3103H NTCLP100E3103H
26103
36103
46103
47 4090K ± 1.5 % NTCLE400E3473H NTCLS100E3473H NTCLP100E3473H
26473
36473
46473
100 4190K ± 1.5 % NTCLE400E3104H NTCLS100E3104H NTCLP100E3104H
26104
36104
46104
Notes
(3) _{Other values and tolerances based on the NTCC100E4 series are available on request. (www.vishay.com/doc?29058)}
(4) _{The specified catalog numbers refer to products with L = 400 mm, without connector and adopt UL-2468.AWG24 wire.}
Document Number: 29060
Revision: 03-May-11
For technical questions, contact: [e-mail]
www.vishay.com
1
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000