IL4216-X001 Datasheet, PDF (1/6 Pages) Vishay Siliconix – Optocoupler, Phototriac Output, High dV/dt, Low Input Current

IL4216, IL4217, IL4218
Vishay Semiconductors
Optocoupler, Phototriac Output, High dV/dt, Low Input Current
A1
6 MT2
C2
5 NC
21842-1
NC 3
i179041-3
4 _MT1
DVE
DESCRIPTION
The IL4216, IL4217, IL4218 consists of an AlGaAs IRLED
optically coupled to a pair of photosensitive non-zero
crossing SCR chips and are connected inversely parallel to
form a TRIAC. These three semiconductors are assembled
in a six pin 0.3 inch dual in-line package.
High input sensitivity is achieved by using an emitter
follower phototransistor and a cascaded SCR predriver
resulting in an LED trigger current of less than 1.3 mA (DC).
The use of a proprietary dV/dt clamp results in a static dV/dt
of greater than 10 kV/μs. This clamp circuit has a MOSFET
that is enhanced when high dV/dt spikes occur between
MT1 and MT2 of the TRIAC. The FET clamps the base of the
phototransistor when conducting, disabling the internal
SCR predriver.
The blocking voltage of up to 800 V permits control of
off-line voltages up to 240 V_AC, with a safety factor more
than two, and is sufficient for as much as 380 V_AC. Current
handling capability is up to 300 mA RMS, continuous at
25 °C.
The IL4216, IL4217, IL4218 isolates low-voltage logic from
120, 240, and 380 VAC lines to control resistive inductive, or
capacitive loads including motors solenoids, high current
thyristors or TRIAC and relays.
FEATURES
• High input sensitivity I_FT = 1.3 mA
• 300 mA on-state current
• High static dV/dt 10000 V/μs, typical
• Very low leakage < 10 μA
• Isolation test voltage 5300 V_RMS
• Compliant to RoHS Directive 2002/95/EC and
in accordance to WEEE 2002/96/EC
APPLICATIONS
• Solid state relay
• Industrial controls
• Office equipment
• Consumer appliances
AGENCY APPROVALS
• UL1577, file no. E52744 system code J
• CSA 93751
• DIN EN 60747-5-5 (VDE 0884) available with option 1
• BSI IEC60950; IEC60065
• FIMKO
ORDERING INFORMATION
I
L
4
2
1
#
-
X
0
#
#
T
DIP
Option 6
PART NUMBER
PACKAGE OPTION
TAPE AND
REEL
7.62 mm
Option 7
10.16 mm
Option 9
AGENCY CERTIFIED/PACKAGE
UL, cUL, BSI, FIMKO
DIP-6
DIP-6, 400 mil, option 6
SMD-6, option 7
SMD-6, option 9
VDE, UL, cUL, BSI, FIMKO
DIP-6
DIP-6, 400 mil, option 6
SMD-6, option 7
SMD-6, option 9
Note
(1) _{Also available in tubes, do not put T on the end.}
600
IL4216
IL4216-X006
IL4216-X007T
IL4216-X009T ⁽¹⁾
600
IL4216-X001
IL4216-X016
-
-
> 0.7 mm
BLOCKING VOLTAGE V_DRM (V)
700
> 0.1 mm
800
IL4217
IL4218
-
IL4218-X006
IL4217-X007
-
IL4217-X009
-
700
800
-
IL4218-X001
-
IL4218-X016
-
IL4218-X017T ⁽¹⁾
-
IL4218-X019T ⁽¹⁾
Document Number: 83630
Rev. 1.6, 20-Oct-10
For technical questions, contact: [e-mail]
www.vishay.com
1