IL420_13 Datasheet, PDF (1/7 Pages) Vishay Siliconix – Optocoupler, Phototriac Output, High dV/dt, Low Input Current

www.vishay.com
IL420, IL4208
Vishay Semiconductors
Optocoupler, Phototriac Output, High dV/dt, Low Input Current
A1
6 MT2
C2
5 NC
21842-1
NC 3
i179035_2
4 MT1
DVE
DESCRIPTION
The IL420 and IL4208 consists of a GaAs IRLED optically
coupled to a photosensitive non-zero crossing TRIAC
network. The TRIAC consists of two inverse parallel
connected monolithic SCRs. These three semiconductors
are assembled in a six pin dual in-line package.
High input sensitivity is achieved by using an emitter
follower phototransistor and a cascaded SCR predriver
resulting in an LED trigger current of less than 2 mA (DC).
The use of a proprietary dV/dt clam results in a static dV/dt
of greater than 10 kV/μs. This clamp circuit has a MOSFET
that is enhanced when high dV/dt spikes occur between
MT1 and MT2 of the TRIAC. When conducting, the FET
clamps the base of the phototransistors, disabling the first
stage SCR predriver.
The 600 V, 800 V blocking voltage permits control of offline
voltages up to 240 VAC, with a safety factor of more than
two, and is sufficient for as much as 380 V_AC.
The IL420, IL4208 isolates low-voltage logic from 120 V_AC,
240 V_AC, and 380 V_AC lines to control resistive, inductive, or
capacitive loads including motors, solenoids, high current
thyristors or TRIAC and relays.
FEATURES
• High input sensitivity I_FT = 2 mA
• 600 V, 800 V blocking voltage
• 300 mA on-state current
• High static dV/dt 10 kV/μs
• Very low leakage < 10 μA
• Isolation test voltage 5300 V_RMS
• Small 6-pin DIP package
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
• Solid state relays
• Industrial controls
• Office equipment
• Consumer appliances
AGENCY APPROVALS
• UL1577, file no. E52744 system code H, double protection
• CSA 93751
• DIN EN 60747-5-5 (VDE 0884), available with option 1
• CQC: GB8898-2001


ORDERING INFORMATION
I
L
4
2
0
#
-
X
0
#
#
T
PART NUMBER
PACKAGE OPTION
TAPE
AND
REEL
DIP-#
7.62 mm
Option 6
Option 7
10.16 mm
Option 8
> 0.7 mm
Option 9
AGENCY CERTIFIED/PACKAGE
UL, cUL, CQC
DIP-6
DIP-6, 400 mil, option 6
SMD-6, option 7
SMD-6, option 8
SMD-6, option 9
VDE, UL, cUL, CQC
DIP-6
DIP-6, 400 mil, option 6
SMD-6, option 7
Note
(1) _{Also available in tubes, do not put T on the end.}
9.27 mm
> 0.1 mm
BLOCKING VOLTAGE V_DRM (V)
600
800
IL420
IL4208
IL420-X006
-
IL420-X007T ⁽¹⁾
IL4208-X007T ⁽¹⁾
IL420-X008T
-
IL420-X009T ⁽¹⁾
IL4208-X009T ⁽¹⁾
600
800
IL420-X001
-
IL420-X016
-
IL420-X017T ⁽¹⁾
IL4208-X017T
Rev. 2.1, 11-Jun-13
1
Document Number: 83629
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000