APD-192G064 Datasheet, PDF (1/1 Pages) Vishay Siliconix – Plasma Panel Display Modules 192 x 64 Graphics Display with Drive Electronics and TTL Level Data Interface

APD-192G064
Vishay Dale
Plasma Panel Display Modules
192 x 64 Graphics Display with
Drive Electronics and TTL Level Data Interface
FEATURES
• TTL level video interface
• Large, bright characters and graphics
• > 30:1 contrast ratio
• Slim profile
• Highly visible for long distance viewing
The APD-192G064 DC Plasma display offers viewing qualities designers seek such as high contrast, viewing angle of 150°
minimum, and long distance readability. It is bright (50 foot lamberts minimum) with characters and graphics figures presented
in a pleasing neon orange color against a black background. Plasma is much more readable and eye-pleasing than liquid
crystal or vacuum fluorescent displays and is filterable to red, amber, or neutral density.
These plasma display panels are driven in a standard row - column refresh method much like a CRT display. The designer
need only supply TTL level signals for SERIAL DATA, DOT CLOCK, COLUMN LATCH, ROW DATA, ROW CLOCK and
DISPLAY ENABLE. The SERIAL DATA is entered with the DOT CLOCK up to frequencies as high as 8mHz. After a row of 192
pixels is clocked in, the COLUMN LATCH signal is toggled and the data is latched. At the time the data is latched, the display
is briefly disabled using the DISPLAY ENABLE signal, then the row pointer is advanced with the ROW CLOCK signal. Once
each frame the ROW DATA must be asserted to synchronize the column serial data with the beginning row. The
recommended scanning frequency is approximately 70 Hz but may be as high as 200 Hz. The high clock rate on the data
clock allows for rapid refresh and maximum access time to the refresh ram.
ELECTRICAL SPECIFICATIONS
Voltages Required: Vsp: + 75 VDC.
Vcc: + 5 VDC.
Vsn: - 110 VDC. Vrw: + 12 VDC (- 98 VDC).
(+ 12 VDC referenced to - 110 VDC.)
Power Required: Typical = 12 watts.
Maximum = 55 watts.
OPTICAL SPECIFICATIONS
Viewing Area: 15.33" [389.38mm] W x 5.09"[129.29mm] H.
Pixel Pitch: 0.080" [2.03mm].
Pixel Size: 0.050" [1.27mm].
Character Array: 8 x 8: 24 x 16. 6 x 8: 32 x 16.
Character Size: 0.48" [12.19mm] W x 0.64" [16.26mm] H.
Luminance: 50 foot lamberts minimum.
DIMENSIONS in inches [millimeters]
192 x 64 Full Field
Pixel Pitch: 0.080 [2.03]
Pixel Size: 0.050 [1.27]
17.055 [433.20]
6.975 ±
0.010
[177.17
± 0.254]
6.663
[169.24]
Center of Active Area
0.156
[3.96]
5.090
[129.29] ^6.19
[157.23]
STANDARD ELECTRICAL SPECIFICATIONS*
DESCRIPTION SYMBOL MIN. TYP. MAX. UNITS
Logic supply
Vcc
+ 4.5 + 5.0 + 5.5
VDC
Anode supply
Vsp
— + 75.0 + 80.0 VDC
Cathode supply
Vsn
— - 110.0 - 125.0 VDC
Cathode control** Vrw + 10.8 + 12.0 + 15.0 VDC
Total Vsp and Vsn Vtot
Logic 1 Input
Vih
170.0 185.0 205.0
2.0
—
—
VDC
VDC
Logic 0 Input
Vil
—
—
0.8
VDC
*Recommended operating voltages. All maximums are absolute
maximum.
**V_rw is referenced to V_sn.
ORDERING INFORMATION
8.527 [216.59]
0.156
[3.96]
15.330 [389.38]
16.68 [423.67]
0.447 ± 0.025
[11.35 ± 0.635]
17.367 ± 0.010
[441.12 ± 0.254]
.. .....
..............
Pin #1
of P1
5.50
[139.70]
Ref.
Pin #1
of P2
11.86 [301.24]
Ref.
3.217 0.403
[81.71] [10.24]
0.840
[21.34]
1.10 [27.94]
Max.
Component
Height
DESCRIPTION
PART NUMBER
Display Module with Drivers and TTL Interface ............................................................................................... APD-192G064
Data Connector ...................................................................................................................................................... 280105-05
Power Connector ................................................................................................................................................... 280108-12
www.vishay.com
2
Document Number: 37012
Revision 07-Nov-00