APD-016M040 Datasheet, PDF (1/3 Pages) Vishay Siliconix – Plasma Panel Display Modules 16 Character Display with Drive Electronics and Controller

APD-016M040
Vishay Dale
Plasma Panel Display Modules
16 Character Display
with Drive Electronics and Controller
FEATURES
• 16 (1 x 16) alphanumeric characters (5 x 7 dot matrix).
• Bezel and filter included.
• Parallel and serial interfaces.
• High brightness.
• Wide viewing angle (150°).
• Low input voltage.
• Compact size.
• Enhanced replacement for Burroughs SSD1000-0061
(optionally-0041).
The APD-016M040 has two modes of operation, parallel or
serial input. The parallel interface consists of a 6 bit data
bus plus 3 hand-shaking and 3 control lines. New charac-
ters are entered from right to left by presenting the appropri-
ate 6 bit code to the data bus and latching it into memory
with a DATA PRESENT pulse. A WRITE CYCLE output
signal is provided during the time in which data can be
written to the display, and a DATA TAKEN pulse occurs after
data has been accepted, or when BACK SPACE occurs.
BACK SPACE allows the displayed message to be shifted to
the right, recalling the last character shifted off the left end
of the display. Up to 16 characters may be recalled, after
which blanks are entered in the left position of the display.
The display may be cleared at any time by bringing the
CLEAR line low. A BLANK DISABLE line is provided to
blank the display without altering the refresh memory
contents.
The serial interface is RS-232-C compatible and has
3 selectable baud rates (300, 1200, 9600). This mode
assumes 1 start bit, 8 data bits, 1 stop bit, no parity and half
duplex. No handshaking is provided. Mode settings and
baud rates are selected as follows. (Both lines are internally
pulled to Vcc with 6.8 kilohm pull-up resistors.)
SS0 SS1 BAUD RATE
0
0
300
0
1
1200
1
0
9600
1
1
Parallel
PIN DESCRIPTION
PIN DESCRIPTION
PIN
1
DATA BIT 5
A
2
DATA BIT 3
B
3
DATA BIT 1
C
4
N/C
D
5
CLEAR
E
6
SPEED SELECT 1
F
7
WRITE CYCLE
H
8
BLANK DISABLE
J
9
SPEED SELECT 0
K
10
N/C
L
Keyway between pins 4 (D) and 5 (E).
DESCRIPTION
DATA BIT 4
DATA BIT 2
DATA BIT 0
DATA PRESENT
BACK SPACE
DATA TAKEN
RECEIVED DATA
+5V
N/C
GND
OPTICAL SPECIFICATIONS
Viewing Area: 0.40" [10.2mm] W x 6.69" [169.9mm] L.
Number of Characters: 16.
Character Size: 0.28" [7.1mm] W x 0.40" [10.2mm] H.
Pixel Size: 0.036" [0.914mm] diameter.
Pixel Pitch: 0.061" [1.55mm].
Character Spacing: 2 blank columns between successive
characters - 0.147" [3.73mm].
Luminance: 80 foot lamberts.
STANDARD ELECTRICAL SPECIFICATIONS
SYMBOL MIN. TYP. MAX. UNITS
Supply Voltage
VCC
4.75 5 5.25
V
Supply Current (1)
ICC
— 1.25 1.75
A
Logic One Voltage
VIH
2
—
—
V
Logic Ø Voltage
VIL
—
—
0.8
V
*Vcc is the input to a DC-DC converter.
There may be peak in rush currents higher than shown.
www.vishay.com
2
Document Number: 37004
Revision 05-Dec-00