93026-38KS Datasheet, PDF (1/4 Pages) Vishay Siliconix – DSCC 93026 SuperTan Wet Tantalum Capacitors

www.vishay.com
DSCC 93026
Vishay
DSCC 93026 SuperTan^® Wet Tantalum Capacitors
Vishay’s DSCC 93026 capacitor represents a major
breakthrough in wet tantalum technology. Its unique
cathode system provides the highest capacitance per unit
volume. The design facilitates a doubling of capacitance,
lower ESR and higher ripple current rating compared
with conventional wet tantalum products. Moreover, the
DSCC 93026 has the capacitance stability of a solid
tantalum capacitor and there are no circuit impedance
restrictions.
The DSCC 93026 is housed in an all tantalum, hermetically
sealed case and is manufactured to withstand hazardous
environments. The DSCC 93026 is used widely in the
defense and aerospace industries and whenever there is a
space problem.
FEATURES
• Terminations: Standard tin/lead (Sn/Pb)
• Very high capacitance
• 10 μF to 1800 μF
• 25 V_DC to 125 V_DC
• - 55 °C to + 125 °C
• Very low ESR
• High ripple current
• All tantalum case
• Hermetically sealed
• Low DCL
• Mounting: Axial
APPLICATION NOTES
a) No continuous reverse voltage permissible.
b) The peak of the applied AC ripple and the applied DC
voltage must not exceed the DC voltage rating of the
capacitor.
c) Ripple current ratings by part number at 85 °C and 40 kHz
are included in the table. Ripple current correction factors
for other temperatures and frequencies are given on the
next page.
d) Transient reverse voltage surges are acceptable under
the following conditions:
The peak reverse voltage does not exceed 1.5 V and the
peak current times the duration of the reverse transient
does not exceed 0.05 As. In addition, the repetition
frequency of the reverse voltage surge is less than 10 Hz.
DIMENSIONS in inches [millimeters]
Terminal welded
to case
0.250 (6.35)
MAX.
0.025 + 0.002
(0.64 + 0.05)
0.094 (2.38)
MAX.
E
L₁
E
CASE CODE
T1
T2
L2
T3
T4
D ± 0.016 [0.41]
0.188 [4.78]
0.281 [7.14]
0.281 [7.14]
0.375 [9.52]
0.375 [9.52]
MAX. INSULATED
(DIA.)
0.219 [5.56]
0.312 [7.92]
0.312 [7.92]
0.406 [10.31]
0.406 [10.31]
Notes
• Material at egress is tantalum
• Insulation sleeving will lap over the ends of the capacitor case
• Tinned nickel leads, solderable and weldable
“D” dia.
Terminal location
within 0.031 of center
L₁ + 0.031 [0.79] UNINSULATED
0.453 [11.51]
0.641 [16.28]
1.008 [25.60]
0.766 [19.46]
1.062 [26.97]
E ± 0.250 [6.35] MAX.
1.500 [38.10]
2.250 [57.15]
2.250 [57.15]
2.250 [57.15]
2.250 [57.15]
• Approx. weight
T1: 2.3 g, T2: 5.7 g
T3: 9.4 g, T4: 14.8 g
Revision: 01-Feb-12
1
Document Number: 40136
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000