732P Datasheet, PDF (1/1 Pages) Vishay Siliconix – Film Capacitors Metalized Polypropylene, Wrap-and-Fill

Type 732P
Vishay Sprague
Film Capacitors
Metalized Polypropylene,
Wrap-and-Fill
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55°C to + 105°C.
Capacitance Range: 1.0µF to 30.0µF.
Capacitance Tolerance: ± 10, ± 5%.
Voltage Rating: 200 WVDC to 600 WVDC.
Dissipation Factor: .10% maximum.
Equivalent Series Resistance: 20kHz - 100kHz (see
Standard Ratings table).
Voltage Test: 200% of rated voltage for 2 minutes.
∆V/∆T: 10 volts/microsecond maximum.
Insulation Resistance: At + 25°C, 100,000
Megohm - Microfarads or 200,000 Megohm minimum.
ENVIRONMENTAL CHARACTERISTICS
Vibration Test (Condition B): No mechanical damage,
short, open or intermittent circuits.
FEATURES
• High stability
• High ripple current to 30A
• Low inductance and low ESR
• Excellent AC performance
DC Life Test: 140% of rated DC voltage for 250 hours at
+ 105°C. No open or short circuits. No visible damage
evident. Maximum Capacitance Change: ± 1.0%.
Minimum IR = 50% of initial limit. Maximum DF = .10%.
Humidity Test: 95% relative humidity at + 40°C for 250
hours. No visible damage evident. Maximum
Capacitance Change: ± 1.0%. Minimum IR = 20% of initial
limit. Maximum DF = .12%.
PHYSICAL CHARACTERISTICS
Lead Pull: 5 pounds (2.3 kilograms) for one minute.
No physical damage.
Lead Bend: After three complete consecutive bends,
no damage.
Marking: Sprague^® trademark, type or part number,
capacitance and voltage.
STANDARD RATINGS in inches [millimeters]
CAP.
(µF)
Max. ESR
PART NUMBER*
(Milliohms)
± 10%
CASE SIZE
20kHz -
TOLERANCE D (Max.) x L ± 0.062 [1.57] 100kHz
MAXIMUM RIPPLE CURRENT (Amps rms) @ 20kHz - 100kHz
Case Temperature @
+ 25°C + 35°C + 45°C + 55°C + 65°C + 75°C + 85°C
200 WVDC
1.0 732P105X9200L 0.531 x 0.750 [13.49 x 19.05] 15.0
2.0 732P205X9200L 0.596 x 0.938 [15.14 x 23.83] 12.0
3.0 732P305X9200L 0.717 x 0.938 [18.21 x 23.83] 11.0
5.0 732P505X9200L 0.733 x 1.250 [18.62 x 31.75] 10.0
10.0 732P106X9200L 0.898 x 1.500 [22.81 x 38.10] 9.0
20.0 732P206X9200L 1.000 x 2.250 [25.40 x 57.15] 8.0
30.0 732P306X9200L 1.200 x 2.250 [30.48 x 57.15] 6.0
9.2
8.5
7.8
7.0
6.0
4.9
4.5
10.8 10.0
9.1
8.2
7.0
5.8
5.3
12.1 11.2 10.3
9.4
8.0
6.5
5.9
13.8 12.7 11.6 10.4
9.0
7.4
8.7
15.0 15.0 14.2 12.7 11.0
9.0
8.2
15.0 15.0 15.0 15.0 13.6 11.1 10.0
15.0 15.0 15.0 15.0 15.0 12.4 11.4
400 WVDC
1.0 732P105X9400L 0.512 x 1.250 [13.00 x 31.75] 20.0
2.0 732P205X9400L 0.698 x 1.250 [17.73 x 31.75] 15.0
3.0 732P305X9400L 0.747 x 1.500 [18.97 x 38.10] 13.0
5.0 732P505X9400L 0.862 x 1.750 [21.89 x 44.45] 11.0
10.0 732P106X9400L 1.030 x 2.250 [26.16 x 57.15] 9.0
20.0 732P206X9400L 1.440 x 2.250 [36.58 x 57.15] 6.0
7.3
7.3
7.3
7.3
7.2
5.9
5.4
12.0 12.0 11.3 10.1
8.7
7.1
6.5
15.0 13.8 12.6 11.3
9.8
8.0
7.3
15.0 15.0 14.7 13.1 11.4
9.3
8.5
15.0 15.0 15.0 15.0 13.8 11.3 10.3
15.0 15.0 15.0 15.0 15.0 14.1 12.8
600 WVDC
1.0 732P105X9600L 0.713 x 1.500 [18.11 x 38.10] 19.0
2.0 732P205X9600L 0.895 x 1.750 [22.73 x 44.45] 15.0
3.0 732P305X9600L 1.086 x 1.750 [27.58 x 44.45] 12.0
5.0 732P505X9600L 1.192 x 2.250 [30.28 x 57.15] 10.0
10.0 732P106X9600L 1.668 x 2.250 [42.37 x 57.15] 6.0
9.5
9.5
9.5
9.5
9.5
7.8
7.1
15.0 15.0 15.0 13.4 11.6
9.5
8.7
15.0
15.0 15.0 15.0 13.1 10.7
9.8
15.0 15.0 15.0 15.0 15.0 12.5 11.4
15.0 15.0 15.0 15.0 15.0 15.0 14.1
* Part Numbers listed are for a capacitance tolerance of ± 10%. To specify ± 5% tolerance, change the "X9" in the Part Number to "X5".
ORDERING INFORMATION
732P
TYPE
105
CAPACITANCE
X9
CAPACITANCE
TOLERANCE
200
DC VOLTAGE
RATING
L
TERMINAL
This is expressed in picofarads. The first two
digits are the significant figures. The third is the
number of zeros to follow. Values must conform
to the decade rating for the tolerance specified.
X9 = ± 10% (Inventoried)
X5 = ± 5%
This is expressed in
volts.
L = Wire leads*
* Leads are bare, solid tinned copper wire. Lead wire sizes are:
Case diameter < .700" [17.78mm], lead AWG No. 20.
www.vishay.com
102
For technical questions, contact [e-mail]
Document Number: 42035
Revision 17-Nov-03