594D476X9016C2T Datasheet, PDF (1/5 Pages) Vishay Siliconix – Solid Tantalum Chip Capacitors TANTAMOUNT® , Conformal Coated, Maximum CV, Low ESR

594D
Vishay Sprague
Solid Tantalum Chip Capacitors
TANTAMOUNT^® , Conformal Coated, Maximum CV, Low ESR
FEATURES
• Large capacitance rating range
• Lowest ESR for a surface mount tantalum chip
capacitor
• Terminations: Tin (2) standard
• 8 mm, 12 mm tape and reel packaging
available per EIA 481-1 and reeling per
IEC 286-3. 7" [178 mm] standard. 13" [330 mm]
available.
• Case code compatibility with EIA 535BAAC and
CECC30801 molded chips
• Compliant to RoHS directive 2002/95/EC
PERFORMANCE/ELECTRICAL CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C
(To + 125 °C with voltage derating)
Note
• Refer to Doc. 40088
Capacitance Range: 1.0 µF to 1500 µF
Capacitance Tolerance: ± 10 %, ± 20 % standard
Voltage Rating: 4 WVDC to 50 WVDC
Equivalent Series Resistance: ESR readings measured at
100 kHz, + 25 °C from 3500 mΩ to 30 mΩ
ORDERING INFORMATION
594D
TYPE
477
CAPACITANCE
X0
CAPACITANCE
TOLERANCE
004
DC VOLTAGE RATING
AT + 85 °C
R
2
CASE CODE TERMINATION
T
PACKAGING
This is expressed in
picofarads. The first two
digits are the significant
figures. The third is the
number of zeros to
follow.
X0 = ± 20 %
X9 = ± 10 %
This is expressed in volts.
To complete the three-digit
block, zeros precede the
voltage rating. A decimal
point is indicated by an “R”
(6R3 = 6.3 V).
See Ratings
and Case
Codes Table
2 = 100 % Tin
4 = Gold plated
8 = Solder
plated (60/40)
Special order
T = Tape and reel
7" [178 mm] reel
W = 13" [330 mm] reel
See tape and reel
specifications.
Notes
• Preferred Tolerance and reel sizes are in bold.
• We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size.
• Voltage substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
W
L
(MAX.)
D
B
(REF.)
A
J
(MAX.)
Tantalum Wire
Nib Identifies
Anode (+)
Terminal
J
(MAX.)
CASE
CODE
L (MAX.)
W
H
A
B
0.158
[4.0]
0.110 + 0.012 - 0.016 0.075 + 0.012 - 0.024 0.031 ± 0.012
[2.8 + 0.3 - 0.4]
[1.9 + 0.3 - 0.6]
[0.80 ± 0.30]
C
0.281
[7.1]
0.126 ± 0.012
[3.2 ± 0.3]
0.098 ± 0.012
[2.5 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.30]
D
0.293
[7.5]
0.170 + 0.012/- 0.024
[4.3 + 0.3/- 0.6]
0.110 ± 0.012
[2.8 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.30]
R
0.283
[7.2]
0.235 + 0.012/- 0.024
[6.0 + 0.3/- 0.6]
0.136 ± 0.012
[3.5 ± 0.3]
0.051 ± 0.012
[1.3 ± .30]
Notes
• The anode termination (D less B) will be a minimum of 0.012" [0.3 mm].
* Pb containing terminations are not RoHS compliant, exemptions may apply
H
B
0.097 ± 0.016
[2.5 ± 0.4]
0.180 ± 0.024
[4.6 ± 0.6]
0.180 ± 0.024
[4.6 ± 0.6]
0.180 ± 0.024
[4.6 ± 0.6]
D (REF.)
0.138
[3.5]
0.236
[6.0]
0.253
[6.4]
0.243
[6.2]
J (MAX.)
0.004
[0.1]
0.004
[0.1]
0.004
[0.1]
0.004
[0.1]
Document Number: 40006
Revision: 11-May-09
For technical questions, contact: [e-mail]
www.vishay.com
85