225P Datasheet, PDF (1/5 Pages) Vishay Siliconix – Polyester Capacitors Filmite “E”, ORANGE DROP, Radial Lead

Type 225P
Vishay Sprague
Polyester Capacitors
Filmite^® “E”, ORANGE DROP^®, Radial Lead
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C
To + 105 °C when working voltage is reduced to 70 % of
+ 85 °C rating; to + 125 °C when working voltage is reduced
to 50 % of 85 °C rating
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25 °C: 100 000 Megohm for C ≤ 0.25 Microfarads
25000 Megohm - Microfarads for C > 0.25 Microfarads
At + 85 °C: 10 000 Megohm for C ≤ 0.15 Microfarads
1500 Megohm - Microfarads for C > 0.15 Microfarads
At + 105 °C: 1500 Megohm for C ≤ 0.17 Microfarads
250 Megohm - Microfarads for C > 0.17 Microfarads
At + 125 °C: 200 Megohm for C ≤ 0.13 Microfarads
25 Megohm - Microfarads for C > 0.13 Microfarads
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.75 %
FEATURES
• Utilizes minimum area where printed wiring
board space is most important
• Wound from PETP polyester film and thin gauge _RoHS
foil under carefully controlled atmospheric _COMPLIANT
conditions
• Protected against moisture by a conformal coating of
epoxy
• Specifically designed for printed wiring board applications
• Widely used in computers, instrumentation and
telecommunications equipment
• 100 VDC through 600 VDC, may be operated up to
+ 125 °C with proper dearting
Dielectric Withstanding Voltage:
Capacitors shall withstand a DC potential of 250 % of rated
voltage applied between terminals for not more than 5
seconds. The test voltage must be applied and discharged
through a resistor of 1 ohm per volt.
Humidity Test:
Condition capacitors with no voltage applied for 72 hours at
95 % relative humidity and + 75 °C. Remove capacitors from
humidity chamber, wipe surface dry of moisture and dry in
circulating air for 4 hours. Measure insulation resistance after
a 2 minute charge at 25 °C and rated voltage or 500 VDC,
whichever is less. Minimum product of insulation resistance
and capacitance shall be 5000 Megohm - Microfarads after
test but need not exceed 10 000 Megohm. Not more than
one failure allowed in 12 units tested.
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test
at + 85 °C at 150 % of rated working voltage. After test,
capacitance shall not have changed by more than 5 % of
initial value, insulation resistance shall not have decreased
by more than 50 % of the initial limit and dissipation factor
shall not have increased to more than 1 %.
DIMENSIONS in inches [millimeters]
L
Max.
L
Max.
Lead
Length
0.237_"
[6.020]
Max.
Lead
Length
0.237
[6.020]
Max.
H
Max.
L
Max.
Lead
Length
0.237
[6.020]
Max.
T Max.
S
± 0.060 [1.524]
Terminal A
CASE
CODE
W
X
Y
Document Number: 42016
Revision: 19-Feb-07
S
± 0.030 [0.762]
Terminal B
L
(Max.)
0.70 [17.78]
0.80 [20.32]
1.25 [31.75]
S
± 0.030 [0.762]
Terminal D
Tinned Copper-Clad Steel
0.032 [0.813] Dia.
(No. 20 AWG)
S
Terminal A and B
0.562 [14.275]
0.613 [15.570]
0.969 [24.613]
Terminal D
0.375 [9.525]
0.375 [9.525]
0.719 [18.263]
For technical questions, contact: [e-mail]
www.vishay.com
25