194D475X0050H2B Datasheet, PDF (1/8 Pages) Vishay Siliconix – Solid Tantalum Chip Capacitors, TANTAMOUNT®, Conformal Coated

www.vishay.com
194D
Vishay Sprague
Solid Tantalum Chip Capacitors,
TANTAMOUNT^®, Conformal Coated
PERFORMANCE CHARACTERISTICS
www.vishay.com/doc?40088
Operating Temperature: - 55 °C to + 125 °C
(above 85 °C, voltage derating is required)
FEATURES
• 8 mm, 12 mm, 16 mm tape and reel
packaging available per EIA-481 and reeling
per IEC 60286-3, 7" [178 mm] standard
• Mounting: Surface mount
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
Note
* Lead (Pb)-containing terminations are not RoHS-compliant.
Exemptions may apply.
Capacitance Range: 0.10 μF to 330 μF
Capacitance Tolerance: ± 10 %, ± 20 % standard
Voltage Rating: 4 V_DC to 50 V_DC
ORDERING INFORMATION
194D
225
X0
TYPE CAPACITANCE CAPACITANCE
TOLERANCE
004
DC VOLTAGE RATING
AT + 85 °C
A
CASE CODE
2
TERMINATION
T
PACKAGING
This is expressed
in picofarads. The
first two digits are
the significant
figures. The third
is the number of
zeros to follow.
X0 = ± 20 %
X9 = ± 10 %
X5 = ± 5 %
Special order
This is expressed in volts.
To complete the
three-digit block, zeros
precede the voltage rating
See Ratings
and Case
Codes table
2 = Gold plated
(50 μ inch minimum)
standard
(RoHS compliant)
8 = 60/40 solder plated
7 = Hot solder dipped
T = T/R (full reel)
7" [178 mm] reel
standard
H = T/R (half reel)
7" [178 mm]
B = Bulk
Note
• Preferred tolerance and reel sizes are in bold.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size.
DIMENSIONS in inches [millimeters]
W
T₁ -
L
P
H
P
T₂ max.
Weld and
dimple
projection
identifies
anode (+)
terminal
CASE CODE
A
W
0.050 ± 0.015
[1.27 ± 0.38]
L
0.100 ± 0.015
[2.54 ± 0.38]
H
0.050 ± 0.015
[1.27 ± 0.38]
P
0.030 ± 0.005
[0.76 ± 0.13]
T₁
0.005
[0.13]
B
0.050 ± 0.015
[1.27 ± 0.38]
0.150 ± 0.015
[3.81 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.030 ± 0.005
[0.76 ± 0.13]
0.005
[0.13]
C
0.050 ± 0.015
[1.27 ± 0.38]
0.200 ± 0.015
[5.08 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.030 ± 0.005
[0.76 ± 0.13]
0.005
[0.13]
D
0.100 ± 0.015
[2.54 ± 0.38]
0.150 ± 0.015
[3.81 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.030 ± 0.005
[0.76 ± 0.13]
0.005
[0.13]
E
0.100 ± 0.015
[2.54 ± 0.38]
0.200 ± 0.015
[5.08 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.030 ± 0.005
[0.76 ± 0.13]
0.005
[0.13]
F
0.135 ± 0.015
[3.43 ± 0.38]
0.220 ± 0.015
[5.59 ± 0.38]
0.070 ± 0.015
[1.78 ± 0.38]
0.030 ± 0.005
[0.76 ± 0.13]
0.005
[0.13]
G
0.110 ± 0.015
[2.79 ± 0.38]
0.265 ± 0.015
[6.73 ± 0.38]
0.110 ± 0.015
[2.79 ± 0.38]
0.050 ± 0.005
[1.27 ± 0.13]
0.005
[0.13]
H
0.150 ± 0.015
[3.81 ± 0.38]
0.285 ± 0.015
[7.24 ± 0.38]
0.110 ± 0.015
[2.79 ± 0.38]
0.050 ± 0.005
[1.27 ± 0.13]
0.005
[0.13]
Note
• When solder coated terminations are required, add 0.015" [0.381 mm] to termination dimension tolerances
T₂ MAX.
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
Revision: 08-Feb-13
1
Document Number: 40000
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000