194D Datasheet, PDF (1/9 Pages) Vishay Siliconix – Solid Tantalum Chip Capacitors MIDGET Conformal Coated

194D
Vishay Sprague
Solid Tantalum Chip Capacitors
MIDGET^® Conformal Coated
FEATURES
• 8mm, 12mm, 16mm tape and reel packaging available per
EIA-481-1 and reeling per IEC 286-3, 7” [178mm] standard.
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55°C to + 85°C.
(To + 125°C with voltage derating.)
Capacitance Range: .10µF - 150µF
Capacitance Tolerance: ± 10%, ± 20% standard.
Voltage Rating: 4 WVDC to 50WVDC.
ORDERING INFORMATION
194D
225
X0
TYPE CAPACITANCE
CAPACITANCE
TOLERANCE
004
DC VOLTAGE RATING
AT + 85°C
A
CASE CODE
2
TERMINATION
T
PACKAGING
This is expressed in
picofarads. The first
two digits are the
significant figures.
The third is the
number of zeros to
follow.
X0 = ± 20%
X9 = ± 10%
X5 = ± 5%
Special Order.
This is expressed in
volts. To complete
the three-digit
block, zeros
precede the voltage
rating.
Note: Preferred Tolerance and reel sizes are in bold.
See Ratings
and Case
Codes
Table.
2 = Gold Plate,
Standard.
(50µ Inch
minimum)
8 = 60/40
Solder Plated
7 = Hot Solder
Dipped
T = Tape and Reel
7" [178] Reel standard.
(1/2 reel minimum)
See Tape and Reel
Specifications.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size.
Voltage substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
-
+
Weld and
W _Dimple
Projection
Identifies
Anode (+)
L
Terminal
H
T₁
P
P
T₂ Max.
CASE
CODE
A
B
C
D
E
F
G
H
W
0.050 ± 0.015
[1.27 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.100 ± 0.015
[2.54 ± 0.38]
0.100 ± 0.015
[2.54 ± 0.38]
0.135 ± 0.015
[3.43 ± 0.38]
0.110 ± 0.015
[2.79 ± 0.38]
0.150 ± 0.015
[3.81 ± 0.38]
L
0.100 ± 0.015
[2.54 ± 0.38]
0.150 ± 0.015
[3.81 ± 0.38]
0.200 ± 0.015
[5.08 ± 0.38]
0.150 ± 0.015
[3.81 ± 0.38]
0.200 ± 0.015
[5.08 ± 0.38]
0.220 ± 0.015
[5.59 ± 0.38]
0.265 ± 0.015
[6.73 ± 0.38]
0.285 ± 0.015
[7.24 ± 0.38]
H
0.050 ± 0.015
[1.27 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.050 ± 0.015
[1.27 ± 0.38]
0.070 ± 0.015
[1.78 ± 0.38]
0.110 ± 0.015
[2.79 ± 0.38]
0.110 ± 0.015
[2.79 ± 0.38]
P
0.030 ± 0.005
[0.76 ± 0.13]
0.030 ± 0.005
[0.76 ± 0.13]
0.030 ± 0.005
[0.76 ± 0.13]
0.030 ± 0.005
[0.76 ± 0.13]
0.030 ± 0.005
[0.76 ± 0.13]
0.030 ± 0.005
[0.76 ± 0.13]
0.050 ± 0.005
[1.27 ± 0.13]
.050 ± 0.005
[1.27 ± 0.13]
T₁
0.005
[0.13]
0.005
[0.13]
0.005
[0.13]
0.005
[0.13]
0.005
[0.13]
0.005
[0.13]
0.005
[0.13]
0.005
[0.13]
Note: When solder coated terminations are required, add 0.015" [0.381] to termination dimension tolerances.
T₂ (Max.)
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
0.015
[0.38]
www.vishay.com
124
For technical questions, contact [e-mail]
Document Number 40000
Revision 05-Jul-02