131P Datasheet, PDF (1/2 Pages) Vishay Siliconix – Film Snubber Capacitors Metal-Case, Paper/Polyester, Dielectric Extended Foil Electrodes

Type 131P
Vishay Sprague
Film Snubber Capacitors
Metal-Case, Paper/Polyester, Dielectric
Extended Foil Electrodes
FEATURES
• Suggested replacement for Type 196P
• Moderate cost
• Small size
• High peak current ratings
• High corona starting voltage
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 65°C to + 125°C.
Capacitance Range: 0.01µF to 0.47µF.
Capacitance Tolerance: ± 20%, ± 10%, ± 5%, ± 2%.
Voltage Rating: 600 WVDC to 1000 WVDC.
Dissipation Factor: 1.0% maximum.
Voltage Test: 200% of rated DC voltage for 2 minutes.
Insulation Resistance: At + 25°C: 20,000 Megohm -
Microfarads or 30,000 Megohm minimum. At + 125°C:
20 Megohm - Microfarads or 250 Megohm minimum.
Capacitance Change with Temperature: At - 65°C,
- 10% typical. At + 125°C, + 10% typical.
ENVIRONMENTAL CHARACTERISTICS
Vibration Test (Condition B): No mechanical
damage, short, open or intermittent circuits.
DC Life Test: 140% of rated voltage for 250 hours @ + 125°C.
No open or short circuits. No visible damage. Maximum
Capacitance Change: ± 5%. Minimum IR = 60% of initial limit.
Maximum DF = 1.0%.
Moisture Resistance: MIL-STD-202, Method 106E, 10
cycles. No visible damage. Maximum Capacitance Change: ±
3%. Minimum IR = 60% of initial limit. Maximum DF = 1.2%.
Thermal Shock and Immersion Cycling: No visible damage.
Maximum Capacitance Change: ± 1%. Minimum IR = 50% of
initial limit. Maximum DF = 1.2%.
PHYSICAL CHARACTERISTICS
Lead Pull: 5 pounds (2.3 kilograms) for one minute.
No physical damage.
Lead Bend: After three complete consecutive bends, no damage.
Lead Wire: Bare, solid tinned wire. Case Diameters: .312"
[7.92mm], No. 22 AWG; .400" [10.16mm] and over, No. 20 AWG.
Marking: Sprague^® trademark, type or part number,
capacitance and voltage.
STANDARD RATINGS in inches [millimeters]
CAPACITANCE
(µF)
PART NUMBER
± 10%
TOLERANCE
NOMINAL CASE SIZE
DxL
Max. rms
CURRENT
@+
85°C
600 WVDC / 370 VAC
0.010
0.022
0.047
0.10
0.22
0.47
131P103X9600S02*
131P223X9600S02*
131P473X9600S02*
131P104X9600S02
131P224X9600S02
131P474X9600S02
0.312 x 0.875 [7.92 x 22.23]
0.400 x 0.875 [10.16 x 22.23]
0.400 x 1.375 [10.16 x 34.93]
0.562 x 1.375 [14.27 x 34.93]
0.670 x 1.625 [17.02 x 41.28]
0.750 x 2.375 [19.05 x 60.33]
0.037
0.058
0.085
0.149
0.354
0.656
Max.
PEAK
CURRENT
@ + 85°C
1.5
3.3
7.0
15.0
33.0
70.0
0.010
0.022
0.047
0.10
0.22
0.47
131P103X91K0S02*
131P223X91K0S02*
131P473X91K0S02*
131P104X91K0S02*
131P224X91K0S02*
131P474X91K0S02*
1000 WVDC / 500 VAC
0.400 x 0.875 [10.16 x 22.23]
0.400 x 1.375 [10.16 x 34.93]
0.562 x 1.375 [14.27 x 34.93]
0.670 x 1.625 [17.02 x 41.28]
0.750 x 2.125 [19.05 x 53.98]
1.000 x 2.375 [25.40 x 60.33]
0.039
0.079
0.133
0.241
0.427
0.772
2.5
5.5
11.0
25.0
55.0
117.0
* All standard inventoried Part Numbers will be stocked in terminal and case style number S04.
Max. rms
CURRENT
@+
125°C
0.025
0.041
0.059
0.104
0.247
0.459
0.027
0.055
0.093
0.168
0.298
0.540
Max.
PEAK
CURRENT
@ + 125°C
1.0
2.3
4.9
10.5
23.1
49.0
1.7
3.8
7.7
17.5
38.5
81.9
ORDERING INFORMATION
131P
TYPE
103
CAPACITANCE
X9
CAPACITANCE
TOLERANCE
600
DC VOLTAGE
RATING
S
TERMINAL
04
CASE
STYLE
This is expressed in picofarads.
The first two digits are the
significant figures. The third is the
number of zeros to follow. Values
must conform to the decade rating
for the tolerance specified.
X0 = ± 20%
X9 = ± 10%
(Inventoried)
X5 = ± 5%
X2 = ± 2%
This is expressed in
volts. (1000 WVDC
coded as 1K0)
S = Wire leads
T = Soldering tab*
Note: Inventoried
items are all S04.
* Soldering tabs are available only on case diameters equal to or greater
than 0.400" [10.16mm]. Consult the factory for special case styles and
terminal configurations.
www.vishay.com
98
For technical questions, contact [e-mail]
Document Number: 42033
Revision 17-Nov-03