PI3106-00-HVMZ_16 Datasheet, PDF (15/26 Pages) Vicor Corporation – Cool-Power ZVS Isolated DC-DC Converter Modules

PI31xx-00-HVMZ
PI3106-00-HVMZ Electrical Characteristics
Unless otherwise specified: 16 V < V_IN < 50 V, 0 A < I_OUT < 4.2 A, -55°C < T_CASE < 100°C⁽¹⁾
Parameter
Symbol
Conditions
Min
Typ
Max Unit
Input Voltage Range
Input dv/dt (1)
Input Under-Voltage Turn-on
Input Under-Voltage Turn-off
Input Under-Voltage Hysteresis
Input Over-Voltage Turn-on
Input Over-Voltage Turn-off
Input Over-Voltage Hysteresis
Input Quiescent Current
Input Idling Power
Input Standby Power
Input Current Full Load
Input Reflected Ripple Current
Recommended Ext Input
Capacitance
V_IN
V_INDVDT
V_UVON
V_UVOFF
V_UVH
V_OVON
V_OVOFF
V_OVH
I_Q
P_IDLE
P_SBY
I_IN
I_INRR
C_IN
Input Specifications
V_IN = 50 V
I_O = 4.2 A
I_O = 4.2 A
I_O = 4.2 A
I_O = 4.2 A
I_O = 4.2 A
I_O = 4.2 A
V_IN = 28 V, ENABLE = 0 V
V_IN = 28 V, I_OUT = 0 A
V_IN = 28 V, ENABLE = 0 V
T_CASE = 100°C I_OUT = 4.2 A η_FL = 88% typical V_IN = 28 V
L_IN = 0.47 µH C_IN = 100 µF 63 V electrolytic
+ 2 x 4.7 µF 50 V X7R ceramic
C_IN = 100 µF 63 V electrolytic + 2 x 4.7 µF 50 V X7R ceramic
C_IN = Cbulk + Chf
16
14.5
13.5
50
51
28
15.4
14.4
1.0
52.3
53.5
1.2
2
3.5
0.056
2.045
13
109.4
50
Vdc
1.0
V/µs
16
Vdc
15.2 Vdc
Vdc
54
Vdc
55
Vdc
Vdc
mAdc
W
W
Adc
mApp
µF
Output Voltage Set Point
Total Output Accuracy
Output Voltage Trim Range
Output Current Range
Over Current Protection
Efficiency – Full Load
Efficiency – Half Load
Output OVP Set Point
Output Ripple Voltage
Switching Frequency
Output Turn-on Delay Time
Output Turn-off Delay Time
Soft-Start Ramp Time
Maximum Load Capacitance
Load Transient Deviation
Load Transient Recovery Time
Maximum Output Power
V_OUT
V_OA
V_OADJ
I_OUT
I_OCP
η_FL
η_HL
V_OVP
V_ORPP
f_SW
t_ONDLY
t_OFFDLY
t_SS
C_OUT
V_ODV
t_OVR
P_OUT
Output Specifications
I_OUT = 2.1 A
-0°C <T_CASE < 100°C
-55°C <T_CASE < 0°C
T_CASE = 100°C, V_IN = 28 V
T_CASE = 100°C, V_IN = 28 V
C_OUT = 6 x 2.2 µF 16 V X7R DC-20 MHz
V_IN = V_UVON to ENABLE = 5 V; V_IN rise time < 1 ms
V_IN = V_UVOFF to ENABLE < 2.35 V
ENABLE = 5 V to 90% V_OUT C_REF = 0
C_REF = 0.22 µF, C_OUT = Al Electrolytic
I_OUT = 50% step 0.1 A/µS
C_OUT = 6 x 2.2 µF 16 V X7R
I_OUT = 50% step 0.1 A/µS
C_OUT = 6 x 2.2 µF 16 V X7R
V_OUT - 1%
12.0
Vdc
-3
+3
%
-5
+3
%
-20%
10%
%
4.2
Adc
4.6
6.8
12
Adc
86
88
%
83
85
%
13.8
14.6
15.3 Vdc
150
mVpp
900
kHz
80
ms
375
µs
230
µs
1000
µF
360
mV
100
µs
50
W
Name
+OUT to -OUT
Continuous Output Current
Peak Output Current
Absolute Maximum Output Ratings
Rating
0.5 to 16 Vdc
4.2 Adc
12 Adc
[1] _{These parameters are not production tested but are guaranteed by design, characterization and correlation with statistical process control.}
Unless otherwise specified, ATE tests are completed at room temperature.
[2] _{Current flow sourced by a pin has a negative sign.}
Cool-Power®
Page 15 of 26
Rev 1.6
02/2015
vicorpower.com
800 927.9474