V048K020T080 Datasheet, PDF (1/15 Pages) Vicor Corporation – VI Chip - VTM Voltage Transformation Module

VTM
V•I Chip^TM – VTM
Voltage Transformation Module
V048K020T080
K indicates BGA configuration. For other
mounting options see Part Numbering below.
• 48 V to 2 V V•I Chip Converter
• 80 A (120 A for 1 ms)
• High density – 320 A/in³
• 125°C operation
• 1 µs transient response
• >3.5 million hours MTBF
Vf = 26 - 55 V
VOUT = 1.1 - 2.3 V
IOUT = 80 A
K = 1/24
ROUT = 1.5 mΩ max
©
• Small footprint – 75 A/in²
• Typical efficiency 94% at 2 V/50 A
• Low weight – 0.5 oz (14 g)
• No output filtering required
• Pick & Place / SMD
• BGA or J-Lead packages
Actual size
Product Description
Absolute Maximum Ratings
The V048K020T080 V•I Chip Voltage Transformation
Module (VTM) breaks records for speed, density and
Parameter
Values
Unit
Notes
efficiency to meet the demands of advanced DSP,
FPGA, ASIC, processor cores and microprocessor
applications at the point of load (POL) while providing
+In to -In
+In to -In
-1.0 to 60.0
Vdc
100
Vdc
For 100 ms
isolation from input to output. It achieves a response
PC to -In
-0.3 to 7.0
Vdc
time of less than 1 µs and delivers up to 80 A in a
TM to -In
-0.3 to 7.0
Vdc
P ^{R E L I M I N A RY volume of less than 0.25 in3 while providing low output}
voltages with unprecedented efficiency. It may be
paralleled to deliver hundreds of amps at an output
voltage settable from 1.1 to 2.3 Vdc.
The VTM V048K020T080’s nominal output voltage is
2 Vdc from a 48 Vdc input factorized bus, Vf, and is
controllable from 1.1 to 2.3 Vdc at no load, and from
1.1 to 2.2 Vdc at full load, over a Vf input range of 26
to 55 Vdc. It can be operated either open- or closed-loop
depending on the output regulation needs of the
application. Operating open-loop, the output voltage
tracks its Vf input voltage with a transformation ratio,
K = 1/24, and an output resistance, ROUT = 1.3 milliohm, to
enable applications requiring a programmable low
output voltage at high current and high efficiency.
VC to -In
-0.3 to 19.0
Vdc
+Out to -Out
-0.1 to 4.0
Vdc
Isolation voltage
Operating junction temperature
2,250
-40 to 125
Vdc
Input to Output
°C
See Note
Output current
80
A
Continuous
Peak output current
120
Case temperature during reflow
208
A
For 1 ms
°C
Storage temperature
-40 to 150
°C
Output power
Peak output power
174
W
Continuous
261
W
For 1 ms
Note: The referenced junction is defined as the semiconductor having the highest temperature.
This temperature is monitored by the temperature monitor (TM) signal and by a shutdown comparator.
Closing the loop back to an input Pre-Regulation
Module (PRM) or DC-DC converter can compensate
for ROUT.
Part Numbering
The 2 V VTM achieves break-through current density of
320 A/in³ in a V•I Chip package compatible with
standard pick-and-place and surface mount assembly
processes. The V•I Chip BGA package supports in-board
mounting with a low profile of 0.16" (4 mm) over the
board. A J-lead package option supports on-board
surface mounting with a profile of only 0.25" (6 mm)
over the board. The VTM’s fast dynamic response and
low noise eliminate the need for bulk capacitance at the
load, substantially increasing the POL density while
improving reliability and decreasing cost.
V 048 K
Voltage
Transformation
Module
Input Voltage
Designator
Configuration Options
F = On-board (Fig.15)
K = In-board (Fig.14)
020 T 080
Output Voltage
Designator
(=VOUT x10)
Output Current
Designator
(=IOUT)
Product Grade Temperatures (°C)
Grade Storage Operating
T
-40 to150 -40 to125
Vicor Corporation
Tel: [phone]
vicorpower.com
V•I Chip Voltage Transformation Module V048K020T080 Rev. 1.2
Page 1 of 15