P024F048T12AL Datasheet, PDF (1/14 Pages) Vicor Corporation – PRM Regulator

P024F048T12AL
PRM^TM
Regulator
• 24 V input V•I Chip^TM PRM
• Vin range 18 – 36 Vdc
• High density – 407 W/in³
• Small footprint – 103 W/in²
• Low weight – 0.5 oz (15 g)
• Adaptive Loop feedback
• ZVS buck-boost regulator
• 1.33 MHz switching frequency
• 95% efficiency
• 125˚C operation (Tj)
©
Vin = 18 – 36 V
Vf = 26 – 55 V
Pf = 120 W
If = 2.5 A
Product Description
The V•I Chip regulator is a very efficient non-isolated
regulator capable of both boosting and bucking a wide
range input voltage. It is specifically designed to provide
a controlled Factorized Bus distribution voltage for
powering downstream VTM^TM Transformer — fast,
efficient, isolated low noise Point-of-Load (POL)
converters. In combination, PRMs and VTMs^TM form a
complete DC-DC converter subsystem offering all of the
unique benefits of Vicor’s Factorized Power
Architecture^TM (FPA)^TM: high density and efficiency; low
noise operation; architectural flexibility; extremely fast
transient response; and elimination of bulk capacitance
at the Point-of-Load (POL).
In FPA systems, the POL voltage is the product of the
Factorized Bus voltage delivered by a PRM and the
"K-factor" (the fixed voltage transformation ratio) of a
downstream VTM. The PRM controls the Factorized Bus
voltage to provide regulation at the POL. Because VTMs
perform true voltage division and current multiplication,
the Factorized Bus voltage may be set to a value that is
substantially higher than the bus voltages typically
found in "intermediate bus" systems, reducing
distribution losses and enabling use of narrower
distribution bus traces. A PRM-VTM chip set can provide
up to 100 A, or 115 W, at a FPA system density of
169 A/in³, or 195 W/in³ — and because the PRM can
be located, or "factorized," remotely from the POL,
these power densities can effectively be doubled.
The PRM described in this data sheet features a unique
"Adaptive Loop" compensation feedback: a single wire
alternative to traditional remote sensing and feedback
loops that enables precise control of an isolated POL
voltage without the need for either a direct connection
to the load or for noise sensitive, bandwidth limiting,
isolation devices in the feedback path.
Absolute Maximum Ratings
Parameter
+In to -In
PC to -In
PR to -In
IL to -In
VC to -In
+Out to -Out
SC to -Out
VH to -Out
OS to -Out
CD to -Out
SG to -Out
Continuous output current
Continuous output power
Case temperature during reflow
Operating junction temperature
Storage temperature
Values
-1.0 to 60.0
-0.3 to 6.0
-0.3 to 9.0
-0.3 to 6.0
-0.3 to 18.0
-0.3 to 59
-0.3 to 3.0
-0.3 to 9.5
-0.3 to 9.0
-0.3 to 9.0
100
2.5
120
225
245
-40 to 125
-40 to 125
DC-DC Converter
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
mA
Adc
W
°C
°C
°C
°C
Notes
MSL 5
MSL 6
T-Grade
T-Grade
VC
VH
PC
SC
0.01 µF T M
SG
IL
OS
NC
P R PRM™ -AL
NC
CD
ROS
10 kΩ
Module
RCD
+In
+Out
V_IN
–In
–Out
Factorized
Bus (V_F)
0.4 µH
10 Ω
+Out
+In
L
+Out
TM _VTM™
O
VC
PC
Module
– Out
A
K
D
Ro – In
– Out
The P024F048T12AL is used with any 048 input series VTM to provide a regulated and
isolated output.
vicorpower.com 800-735-6200
V•I Chip Regulator
P024F048T12AL
Rev. 3.1
Page 1 of 14