TFS35A Datasheet, PDF (3/5 Pages) Vectron International, Inc – Filter specification

TFS35A.doc
VI TELEFILTER
Filter specification
version 1.4
TFS 35A
06.04.2003
3/5
5.1. 100% Screening Tests :
After the following tests the filter shall meet the whole specification. Electrical tests after test 4, test 5 and 7.
1. Internal Visual Inspection: according to MIL-STD-883 method 2017
2. Stabilization Bake:
16 hrs at 125°C under Vacuum according to MIL-STD-883 Method 1008 Condition B
3. Temperature Cycling:
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N equivalent MIL-STD-202 Method 107
4. Shock:
500g, 18 ms, half sine wave, 3 shocks each plane;
5. Burn-in:
6. Seal test:
DIN IEC 68 T2 - 27
160hrs at 125°C ( no input power ) according to MIL-STD-883 Method 1015
gross leak bubble test – Fluorocarbon liquid at 125°C ± 5°C
MIL-STD-202 Method 112 Condition D
Fine leak spot test – Helium detector according to MIL-STD-202 Method 112 Condition C
7. External Visual Inspection: according to MIL-STD-883 method 2009
5.2. Qualification Tests :
1. Resistance to
solder heat (reflow):
2. Vibration:
3. Life test:
reflow possible: twice max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 – 6
storage of 2 pcs for 1000 hrs at 125°C ( no input power ) MIL-STD-883 Method 1005. The test will
be done using samples which were handled according to point 5.1.
6. Packing :
Tape & Reel:
DIN IEC 286 - 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
Trailer
1700
min 300 mm
min 500 mm
min 300 mm
Tape (all dimensions in mm)
W
: 24± 0,3
Po
:4
± 0,1
Do
: 1,5 + 0,1
E
: 1,75 ± 0,1
F
: 11,5 ± 0,1
G (min) : 0,6
CT
P2
:2
± 0,1
P1
: 12 ± 0,1
D1(min) :
Ao
:
Bo
:
CT
:
1,5
7,1 ± 0,2
13,9 ± 0,2
21,5 ± 0,1
Reel (all dimensions in mm):
A
:
W1
:
W2(max) :
N(min) :
C
:
330
24,4 + 2
30,4
60
13 +0,5/-0,2
COVER TAPE
EMBOSSED CARRIER TAPE
Do
Po
P2
Ao
D1
Bo
P₁
E
F
W
G
W₂
C
N
A
W₁
The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape.
Markings on the filters can be read if the upper side of the carrier tape is regarded with the sprocket holes on its right.
TELEFILTER GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: [phone] / Fax: [phone]
E-Mail: [e-mail]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of
their use or application. No rights under any patent accompany the sale of any such product(s) or information.