TFS228 Datasheet, PDF (3/5 Pages) Vectron International, Inc – Filter specification

t_{_}fs_{_}2_{_}28_{_}._{_}do_{_}c_{__________________________________________________________}V_{_}e_{_}r_{_}s_{_}io_{_}n_{_}1_{_}.3_{_______________________}0_{_}2_{_}.1_{_}0_{_}.2_{_}0_{_}0_{_}0_{_}
V_{__}I_{__}T_{__}E_{_}L_{__}E_{__}F_{_}I_{_}L_{_}T_{__}E_{_}R_{_______________________}F_{__}il_{_}t_{_}e_{_}r_{___}s_{_}p_{__}e_{_}c_{_}i_{_}f_{_}i_{_}c_{_}a_{_}t_{_}i_{_}o_{_}n_{_____________________}T_{_}F_{__}S_{___}2_{_}2_{_}8_{_________}3_{__}/5_{_}
Stability Characteristics:
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 18 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 - 6
3. Damp heat:
(cycle)
25 °C to 55°C / 95% r.H. / 10 cycles
DIN IEC 68 - 2 – 30 Db
4. Resistance to
solder heat (reflow):
max. 2 times reflow process;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
Packing:
Tape & Reel:
IEC 286 - 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
Real of empty components at start:
Real of empty components at start including leader:
Trailer
3000
min 300 mm
min 500 mm
min 300 mm
Tape (all dimensions in mm)
W
: 16 ± 0,3
Po : 4 ± 0,1
Do : 1,5 + 0,5
E
: 1,75 ± 0,1
F
: 7,5 ± 0,1
G (min) : 0,6
P2 : 2 ± 0,1
Ct
P1 : 8 ± 0,1
D1(min) : 1,5
Ao : 5,5 ± 0,1
Bo : 7,5 ± 0,1
Ct
: 13,5+/-0,1
COVER TAPE
EMBOSSED CARRIER TAPE
Do
Po
P2
Ao
D1
Bo
E
F
W
G
P1
Reel (all dimensions in mm):
A
:
330
W1
:
W2 (max) :
16,4 +2
22,4
N (min)
: >= 50
C
C
:
13 + 0,5
A
- 0,2
W2
N
W1
The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape.
The marking of the filters is readable if the sprocket holes are on the left side of the tape, i.e. pin 1 identifier is close to the
sprocket holes.
______________________________________________________________________________________________________
VI TELEFILTER
Vectron International, Inc.
Potsdamer Straße 18
267 Lowell Road
D 14 513 TELTOW / Germany
Hudson, NH 03051 / USA
Tel: [phone] / Fax: [phone]
Tel: [phone] Fax: [phone]
E-Mail: [e-mail]
E-Mail: [e-mail]
______________________________________________________________________________________________________
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.