TFS70BE Datasheet, PDF (1/5 Pages) Vectron International, Inc – Filter specification

Filename: TFS70BE.doc
Vectron International
Version 1.2
Filter specification
TFS 70BE
26.11.2012
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
23
°C
0
dBm
1.6 Ω || -7.7 pF
1.75 Ω || -7.5 pF
Characteristics
Remark:
The reference level for the relative attenuation arel of the TFS 70BE is the minimum of the pass band attenuation amin. The minimum of the pass band
attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB
filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 70.0 MHz without any tolerance. The given values for both the
relative attenuation arel and the group delay ripple have to be achieved at the frequencies given below even if the centre frequency fc is shifted due to the
temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc.
Data
Insertion loss
ae
(reference level)
Nominal frequency
fN
Centre frequency at ambient temperature
fC
Pass band
PB
Pass band variation
Amplitude ripple in any 112.5 kHz segment in PB
Relative attenuation
fN
fN ±
fN ±
fN +
… fN ±
1.1 MHz … fN ±
1.5 MHz … fN ±
0.3 MHz … fN -
3.0 MHz … fN +
Group delay
Group delay ripple within PB
(in any 112.5 KHz segment in PB)
Phase linearity within PB
(in any 112.5 KHz segment in PB)
Input power level
arel
0.5 MHz
1.5 MHz
3.0 MHz
3.0 MHz
1.0 GHz
at fN
p-p
Operating temperature range
Storage temperature range
Frequency inversion temperature
Temperature coefficient of frequency
OTR
TCf ***
typ. value
13.3 dB
-
70.0 MHz
-
0.4 dB
0.15 dB
0.4 dB
42
dB
42
dB
53
dB
52
dB
2.35 µs
70
ns
2.0 deg
-
-
-
25
°C
- 0.036 ppm/K²
tolerance / limit
max.
15.0 dB
fN ±
max.
max.
70.0 MHz
-
0.5 MHz
0.8 dB
0.5 dB
max.
min.
min.
min.
min.
max.
max.
0.8 dB
37 dB
40 dB
50 dB
50 dB
4 µs
120 ns
max.
5 deg
max.
23 ** dBm
- 40 °C ... + 70 °C
- 40 °C ... +100 °C
-
-
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values
only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) This power level is only allowed for short term operation (10% of the life time), the max. input power for continuous operation is max.15dBm only
***) ∆f(Hz) = TCf(ppm/K²) x (T-T0)² x fTo(MHz)
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: [phone] / Fax: [phone]
E-Mail: [e-mail]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.