VS3V253 Datasheet, PDF (3/6 Pages) Vaishali Semiconductor – High-speed 3.3V CMOS VSwitch Dual 4:1 Mux/Demux

VS3V253/VS3V2253
Advance Information
Table 5. Recommended Operating Conditions
Symbol
Parameter
Conditions Min Typ Max Units
VCC
Power supply voltage
2.3
3.6 V
VIL
Low level input voltage
(Control inputs)
Vcc = 2.3 to 2.7
Vcc =2.7 to 3.6
0.7 V
0.8
VIH
High level input voltage
Vcc = 2.3 to 2.7 1.7
V
(Control inputs)
Vcc = 2.7 to 3.6 2.0
TA
Operating free-air temperature
-40
85
o_C
Note: All unused control inputs of the device must be held at Vcc or GND, to ensure proper device operation
Table 6. Electrical Characteristics Over Recommended Operating Free-air Temperature Range
Symbol
Parameter
Test Conditions
Min Typ Max Units
VIK
Clamp Voltage
Control Inputs VCC = Min, IIK = -18 mA
-1.5 V
Switch I/O
-1.5
VOH
Logic High Voltage
Switch I/O
VIN = VCC = 3.3V, IOUT = -100µA 2.3
VIN = VCC = 2.5V, IOUT = -100µA ^1.5
2.7 V
2.0
II
Input Leakage Current Control Inputs VCC = Max, VI = VCC or GND
1
µA
|OFF|
Power OFF Leakage Control Inputs VCC = 0, VI or VO = VCC or GND
Current
Switch I/O
1
µA
|IOZ|
OFF State Leakage
Switch I/O
VCC = Max, VI/O = VCC,
Current
/EA = /EB = VCC
1
µA
IODL
Switch I/O Drive
VCC = 3.0V, VIN = 0,
VS3V253
50
mA
Current (Logic LOW) _{VOUT = 0.7V}
VS3V2253
30
mA
IODH
Switch I/O Drive
VCC = 3.0V, VIN = VCC,
Current (Logic HIGH) _{VOUT = 1.8V}
RON
Switch ON
Resistance⁽¹⁾
VCC = 3.0V, VIN = 0,
IOUT = 15mA
VCC = 2.3V, VIN = 0V,
IOUT = 8mA
VS3V253
VS3V2253
VS3V253
VS3V2253
VS3V253
VS3V2253
-50
mA
-20
mA
5⁽²⁾
7
Ω
20
28⁽²⁾ 40
Ω
10⁽³⁾ 14
Ω
23
35⁽³⁾ 48
Ω
Notes:
1. RON is measured by forcing specified current into the ‘output’ node of the switch with the ‘input’ node of the switch
at the specified voltage.
2. Typical value is specified at VCC = 3.3V and TA = 25^oC.
3. Typical value is specified at VCC = 2.5V and TA = 25^o
Table 7. Power Supply Characteristics Over Recommended Operating Free-air Temperature Range
Symbol
Parameter
Test Conditions ⁽¹⁾
Max Units
ICCQ
Quiescent Power Supply Current
VCC = 3.6V, SX, /EX = VCC or GND, f = 0
1
µA
∆ICC
QCCD
Power Supply Current per Input High
(2) _{(Control Inputs)}
Dynamic Power Supply Current ⁽³⁾
VCC = 3.6V, VIN = 3.0V, f = 0
VCC = 2.7V, VIN = 2.0V, f = 0
VCC = Max, Switch pins open,
Control Inputs toggling at 50% duty cycle
300 µA
0.15 mA/MHz
Notes:
1. For conditions shown as Min or Max, use the appropriate values per Recommended Operating Conditions.
2. Per control input. All other control inputs at GND. Switch I/O pins do not contribute to ∆ICC.
3. This parameter represents the average DC current resulting from the switching of internal nodes of the device at a
given frequency. The switch I/O pins make insignificant contribution to the dynamic power supply current of the
device. This parameter is guaranteed, but not production tested.
2000-11-28
Page 3
MDSS-0003-01
Vaishali Semiconductor 1300 White Oaks Road Campbell CA 95008 Ph. 408.377.6060 Fax [phone]