L1183A Datasheet, PDF (4/5 Pages) Unisonic Technologies – 300mA CMOS LDO

L1183A
Preliminary
CMOS IC
„ ABSOLUTE MAXIMUM RATING
PARAMETER
SYMBOL
RATINGS
UNIT
Input Voltage
Input Voltage (EN,BYP)
V_IN
-0.3~ +8
V
-0.3~ +8
V
Output Voltage
V_OUT
-0.3~ V_IN+0.3
V
Output Voltage
I_OUT
P_D / (V_IN - V_OUT)
mA
Power Dissipation
P_D
400
mW
Junction Temperature
T_J
150
°C
Storage Temperature
T_STG
-65~ +150
°C
Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
„ RECOMMENDED OPERATING CONDITIONS
PARAMETER
SYMBOL
RATINGS
UNIT
Ambient Temperature
Ta
- 40~ +85
°C
Junction Temperature
Storage Temperature
„ THERMAL DATA
T_J
T_STG
- 40~ +125
°C
-65~ +125
°C
PARAMETER
SYMBOL
RATINGS
UNIT
Junction to Ambient
θ_JA
280
Junction to Case (Note)
θ_JC
140
Note: θ_JC on center of molding compound if IC has on tab
„ ELECTRICAL CHARACTERISTICS (T_a = 25°C, Unless otherwise specified)
°C/W
°C/W
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNIT
Input Voltage
Line Regulation
Load Regulation
V_IN
ΔVOUT
VOUT
ΔVOUT
VOUT
V_IN=V_OUT+1~V_OUT+2
I_OUT=1mA
1.2V≤V_OUT≤1.4V
1.4V<V_OUT≤2.0V
2.0V<V_OUT<4.0V
I_OUT=1mA~300mA
Note1
6.5 V
-0.2
0.2 %
-0.15
0.15 %
-0.1 0.02 0.1 %
-1 0.2 1
%
Output Voltage Accuracy
Quiescent Current
Dropout Voltage
Power Supply Ripple
Rejection
I_OUT=1mA
-1.5
1.5 %
I_OUT=300mA
-2.5
2.5 %
I_Q
I_OUT=0mA
30 50 µA
V_D
I_OUT=300mA
1.2V≤V_O(NOM)≤2.0V
V_OUT=V_O(NOM)-2.0% 2.4V<V_O(NOM)≤2.8V
1300 mV
400 mV
PSRR ^IOUT=100mA
C_OUT=2.2µF
f=100Hz
f=1kHz
f=10kHz
60
dB
50
dB
20
dB
Output Voltage Noise
Output Current
Current Limit
Short Circuit Current (Note2)
Ground Pin Current
Over Temperature Shutdown
eN
I_OUT
I_LIMIT
I_SC
I_GND
OTS
I_OUT=10mA,C_OUT=2.2µF,f=10Hz~100kHz,
V_OUT>1.2V
V_OUT>1.2V
V_OUT<0.8V
I_OUT=1mA ~300mA
30
300
µV_RMS
mA
300 450
mA
150 300 mA
35
µA
150
°C
Over Temperature Hysteresis OTH
30
°C
Temperature Coefficient of
Output Voltage
T_CV_O
30
ppm/°C
EN Input Threshold
V_EH V_IN=2.7V~6.5V
V_EL V_IN=2.7V~6.5V
2.0
V_IN
V
0
0.4 V
EN Input Bias Current
I_EH V_EN=V_IN, V_IN=2.7V~6.5V
I_EL V_EN=0V, V_IN=2.7V~6.5V
0.1 µA
0.5 µA
Shutdown Supply Current
I_SD V_IN=5V, V_O=0V, V_EN<V_EL
0.5 1 µA
Shutdown Output Voltage
V_SD I_O=0.4mA, V_EN<V_EL
0
0.4 V
Notes:1. V_IN(MIN) =V_OUT +V_D
2. To prevent the short circuit current protection feature from being prematurely activated, the input voltage
must be applied before a current source load is applied.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
4 of 5
QW-R502-315.d