L2044 Datasheet, PDF (3/3 Pages) Unisonic Technologies – DUAL OUTPUT FLASHER

L2044
LINEAR INTEGRATED CIRCUIT
ABSOLUATE MAXIUM RATINGS
PARAMETER
SYMBOL
RATINGS
UNIT
Supply Voltage, 1 min, pins 5, 9 and 12
Junction Temperature
Operating Temperature
Storage Temperature
V_CC
24
V
T_J
+125
Â¥
T_OPR
0Ċ~70Ċ
Â¥
T_STG
-40 ~ +150
Â¥
Thermal Resistance Junction to Ambient
DIP-14
ǀ_JA
SOP-14
90
Â¥/W
120
Note 1.Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
2.The device is guaranteed to meet performance specification within 0Ċ~70Ċ
operating temperature range
and assured by design from –20Ċ~85Ċ.
ELECTRICAL CHARACTERISTICS (V_CC = 12V, T_a =25Â¥, unless otherwise specified.)
PARAMETER
Supply Voltage Range
Saturation Voltage
V_CC=8V
V_CC=12V
Clamping Voltage
Relay output overvoltage detection (relay disabled)
Control signal threshold
Output current for relay driver
Relay output reverse current
Supply current, switches open
Relay coil resistance
Start delay
Tolerance of control signal threshold
Temperature coefficient of control signal Threshold
SYMBOL TEST CONDITIONS
V_CC Pins 5, 9, 12
V_OUT R_L=82Ω
V₁₂
V₁₂
V_CC
I_OUT
I_OUT
I_CC
R_L
t_ON
T_CV_O
T_a= -20Â¥ ~ 85Â¥
T_a= -20Â¥ ~ 85Â¥
V_CC=9V
V_CC=13.5V
V_CC=16V
Pins 11, 13
Pins 11, 13
Pins 5, 9, 12
First bright phase
V_CC=9V~16V, Pin 8,
T_a= -20Â¥ ~ 85Â¥
V_CC=13.5V, Pin 8
TOLERANCES (V_CC = 12V, T_a =25Â¥, unless otherwise specified.)
MIN
8
25.0
18
-6
TYP MAX UNIT
18 V
1.0 _V
1.2
27.5 30.0 V
20 22 V
70.6
85.5
mV
93.0
300 mA
0.1 mA
10 µA
Ω
10 ms
+6 %
10
µV/K
PARAMETER
Frequency determining resistor
Frequency determining capacitor
Frequency tolerance
Bright period

Frequency increase

Lamp load






SYMBOL
TEST CONDITIONS
R₁
C₁
¶f₁
¶f₁
¶f₂

Normal flashing, basic frequency f₁
excluding the tolerance of R₁ and C₁
Basic frequency f₁
Control frequency f₂
f₂ Lamp failure
P_L
MIN TYP MAX UNIT
6.8
510 kΩ
47 µF
-5
+5 %
47
37
2.15×f₁
1
53 _%
45
2.3×f₁ Hz
W
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
3
QW-R123-015,A