UM9636_16 Datasheet, PDF (3/7 Pages) Union Semiconductor, Inc. – High-Speed Dual SPDT Switch

UM9636
Electrical Characteristics
Symbol
Parameter
DC Electrical Characteristics
Test Conditions
Limits (–40°C to 85°C)
V+ (V) Temp
Min
Typ
(Note 1)
Max
Unit
VANALOG
ICC
IGND
IIH
IIL
ID(on)
ID(off)
IS(off)
VIH
Analog Signal Range
Quiescent Supply
Current
Ground Current
Input Leakage
Current, VIN High
Input Leakage
Current, VIN Low
Channel On Leakage
Current
OFF State Leakage
Current
(Note 2)
Input High Voltage
VIN=0V, or V+
VAX=1.65V
VAX=0.5V
V+=12V,
VD=VS 11V/1V
V+=12V,
VD=1V/11V,
VS=11V/1V
Full
Room
12
Full
Room
-0.5
Full
-1
12
Full
-0.1
0.01
-0.01
0.01
12
V
0.5
1
μA
0.1
μA
12
Full
-0.1
0.01
0.1
μA
12
Room
Full
-1.0
±0.01
1.0
2.0
μA
12
Room
Full
-11.0
±0.01
11.0
15.0
μA
12
Room
Full
-11.0
±0.01
11.0
15.0
μA
12
Full
1.65
V
VIL
Input Low Voltage
12
Full
RON
ΔRON
RFLAT
On-Resistance
(Note 3)
On Resistance Match
Between Channels
(Note 3, 4, 5)
On Resistance
Flatness
(Note 3, 4, 6)
VD=11.3V
IS=1mA
VD=11.3V
IS=1mA
VD=0.7, 6.5, 11.3V
IS=1mA
12
Room
Full
12
Room
Full
12
Room
Full
AC Electrical Characteristics
tON
Turn On Time
RL=300Ω, CL=35pF
12
Room
Full
tOFF
Turn Off Time
RL=300Ω, CL=35pF
12
Room
Full
tBBM
Break Before Make
Time (Note 7)
RL=300Ω,
CL=35pF
12
Room
Full
5
2
THD
Total Harmonic
Distortion
Signal=1VRMS,
20Hz to 20kHz,
RL=600Ω
12
Room
Charge
Injection
QINJ
CL=1nF, RGEN=0Ω,
VGEN=0V
12
Room
OIRR
Off Isolation
(Note 8)
RL=50Ω, CL=5pF,
f=10MHz
12
Room
XTALK
Crosstalk
RL=50Ω, CL=5pF,
f=10MHz
12
Room
BW
-3dB Bandwidth
RL=50Ω
12
Room
0.5
V
83
110
125
Ω
2
4
6
Ω
33
45
50
Ω
30
70
80
ns
15
55
65
ns
15
ns
0.01
%
23.5
pC
-58
dB
-67
dB
720
MHz
Capacitance
CIN
Control Pin Input
Capacitance
f=1MHz
Room
3
pF
COFF
Switch Off
Capacitance
f=1MHz
12
Room
2.0
pF
CON
Switch On
Capacitance
f=1MHz
12
Room
7.7
pF
Note 1: Typically values are at TA=+25°C.
Note 2: The high OFF State Leakage Current is because of pull down resistor
Note 3: Guaranteed by design. Resistance measurements do not include test circuit or package resistance.
Note 4: Parameter is characterized but not tested in production.
Note 5: ΔRON=︱RON (S1A/S1B)−RON(S2A/S2B)︱measured at identical VCC, temperature and voltage levels.
Note 6: Flatness is defined as the difference between the maximum and minimum value of On Resistance over the specified range of
conditions.
Note 7: Guaranteed by design.
Note 8: Off Isolation=20log10 [VD/VSA/SB].
________________________________________________________________________
http://www.union-ic.com Rev.05 Apr.2016
3/7