UM603A Datasheet, PDF (4/6 Pages) Unisonic Technologies – DUAL OPERATIONAL AMPLIFIER AND CURRENT CONTROLLER

UM603A
LINEAR INTEGRATED CIRCUIT
 ELECTRICAL CHARACTERISTICS (Cont.)
V_CC+=+5V, V_CC=Ground, V_OUT=1.4V, T_A=25C (unless otherwise specified)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
OPERATOR2 (independent op-amp)(Note 1)
Input Offset Voltage
UM603A-1
UM603A-2
V_I(OFF)
T_A=25C
T_MIN≤T_A≤T_MAX
T_A=25C
T_MIN≤T_A≤T_MAX
Input Offset Voltage Drift
DV_I(OFF)
Input Offset Current
I_I(OFF)
T_A=25C
T_MIN≤T_A≤T_MAX
Input Bias Current
I_I(BIAS)
T_A=25C
T_MIN≤T_A≤T_MAX
Large Signal Voltage Gain
A_VD
V_CC=15V, R_L=2k, V_OUT=1.4V~11.4V
T_MIN≤T_A≤T_MAX
50
25
Supply Voltage Rejection Ratio
SVRR V_CC=5V ~30V
65
Input Common Mode Voltage Range
V_I(CM)
V_CC=+30V (Note 1)
T_MIN≤T_A≤T_MAX
0
0
Common Mode Rejection Ratio
CMRR _{TMIN≤TA≤TMAX}
70
60
Output Current Source
I_O(SOURCE) V_CC=+15V, V_OUT=2V, V_JD=+1V
20
Short Circuit to Ground
I_SC V_CC=+15V
Output Current Sink
I_O(SINK) V_ID=-1V, V_CC=+15V, V_OUT=2V
10
High Level Output Voltage
V_OH V_CC+=30V
T_A=25C, R_L=10k 27
T_MIN ≤ T_A ≤ T_MAX
27
Low Level Output Voltage
V_OL
R_L=10k
T_MIN≤T_A≤T_MAX
Slew Rate at Unity Gain
SR
V_IN=0.5 ~ 3V, V_CC=15V
R_L=2k, C_L=100pF, unity gain
0.2
Gain Bandwidth Product
GBP
V_CC=30V, R_L=2K, C_L=100pF
f=100kHz, V_IN=10mV
0.5
Total Harmonic Distortion
THD
f=1kHz , C_L=100pF, V_OUT=2V_PP
Av=20dB, R_L=2k, V_CC=30V,
 VOLTAGE REFERENCE
TYP MAX UNIT
0.5
2
3
mV
1
4
5
mV
7
μV/C
2
30
50
nA
20
150
200
nA
100
V/mV
100
dB
(V_CC+)-1.5
V
(V_CC+)-2
85
dB
40
mA
40 60 mA
20
mA
28
V
5
5
20
20
mV
0.4
V/μs
0.9
MHz
0.02
%
PARAMETER
Cathode Current
SYMBOL
I_K
Value
1 ~ 100
UNIT
mA
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNIT
UM603A-1
Reference Input Voltage
UM603A-2
±0.4%, T_A=25C
2.49 2.5 2.51
V_REF
T_MIN≤T_A≤T_MAX, V_KA=V_REF, I_KA=10mA 2.48
±1%, T_A=25C
2.475
2.5
2.52
2.525
T_MIN≤T_A≤T_MAX, V_KA=V_REF, I_KA=10mA 2.45
2.55
V
Reference Input Voltage Deviation
Over Temperature Range
△V_REF ^VKA^=VREF^{, I}K^{=10mA, T}MIN^≤TA^≤TMAX
7
30 mV
Minimum Cathode Current for
Regulation
I_MIN V_KA=V_REF
0.5
1
mA
Dynamic Impedance(Note 2)
∣Z_KA∣ V_KA=V_REF, △I_K=1~100mA, f<1kHz
0.2 0.5 Ω
Notes: 1. The input common-mode voltage of either input signal voltage should not be allowed to go negative by
more than 0.3V. The upper end of the common-mode voltage range is V_CC+ -1.5V. But either of both
inputs can go to +36V without damage.
_{2. The dynamic impedance is defined as「ZKA」=}
VKA
IK
.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
4 of 6
QW-R105-031.F