TS5218 Datasheet, PDF (2/7 Pages) Taiwan Semiconductor Company, Ltd – 800mA Ultra Low Dropout Voltage Regulator with Enable

TS5218
800mA Ultra Low Dropout
Voltage Regulator with Enable
Electrical Characteristics
V_IN = V_OUT + 1V, V_IN =2.5V for fixed reference output voltage, Venable= 2.25V, Ta = 25^oC, unless otherwise specified.

Parameter
Conditions
Min
Typ
Max
Unit
Fixed Reference Output Voltage
Line Regulation
Load Regulation
Output Voltage Temp. Coefficient
I_L=10mA
10mA ≤ I_L ≤ 800mA,
2.5V ≤ V_IN ≤ 16V
I_L=10mA, Vo+1V ≤ V_IN ≤ 16V
V_IN =Vout+1V, 8mA≤I_L≤300mA
V_IN =Vout+1V, 10mA≤I_L≤800mA
0.980|Vo|
0.970|Vo|
--
--
--
--
1.24
(V_REF)
0.05
0.05
0.2
40
1.020|Vo|
V
1.030|Vo|
0.5
%
0.1
%
1.0
100
ppm/ ^oC
Dropout Voltage (Note 5)
Quiescent Current (Note 6)
Current Limited
Input Logic Voltage
ΔV_OUT = -1%
V_IN= V_OUT +1V
I_L=100mA
I_L=400mA
I_L=800mA
I_L=100mA
I_L=500mA
I_L=800mA
V_OUT =0, V_IN = V_OUT +1V
Low (OFF)
High (ON)
--
100
250
--
300
380
mV
--
400
700
--
0.7
2
--
4.0
6
mA
--
12.0
20
--
1.8
--
A
--
--
0.8
V
2.25
--
--
Enable Pin Input Current
V_EN =2.25V
V_EN =0.8V
--
--
75
uA
--
--
4
Adjust Pin Bias Current
--
40
120
nA
Reference Voltage Temp. Coefficient
(Note 8)
--
20
--
ppm/ ^oC
Adjust Pin Bias Current Temp. Coefficient
--
0.1
--
nA/ ^oC
Note:
1. Absolute Maximum Rating is limits beyond which damage to the device may occur. For guaranteed specifications
and test conditions see the Electrical Characteristics.
2. The device is not guaranteed to operate outside its operating rating.
3. Devices are ESD sensitive. Handling precautions recommended.
4. The maximum allowable power dissipation is a function of the maximum junction temperature, T_J, the junction to
ambient thermal resistance, Ó¨_JA, and the ambient temperature, Ta. Exceeding the maximum allowable power
dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. The effective
value of Ө_JA can be reduced by using a heat sink, Pd_(max) = (T_J(max) – Ta) / Ө_JA.
5. Dropout voltage is defined as the input to output differential at which the output voltage drops -1% below its nominal
value measured at 1V differential.
6. Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the
ground pin current and output load current, I_GND = I_IN - I_OUT for fix output voltage, I_GND = I_IN - I_OUT +10mA for fix
reference output voltage in full load regulation.
7. V_REF ≤ V_OUT ≤ (V_IN – 1V), 2.25V ≤ V_IN ≤ 16V, 10mA ≤ I_L ≤ 1.0A.
8. Output voltage temperature coefficient is ΔV_OUT (worse cast) / (T_J(max) – T_J(MIN)) where is T_J(max) +125^oC and T_J(MIN) is
0^oC.




2/7
Version: A09