TMP110 Datasheet, PDF (1/2 Pages) Tumbler Technologies + TRUMPower – 110 WATT MEDICAL POWER ADAPTERS

TRUMPower
DESCRIPTION
The TMP110 series of AC/DC switching power
adapters are for 110 watts of continuous
output power. They are enclosed in a 94V-1
rated polyphenylene-oxide case with an IEC
320 inlet to mate with interchangeable cord for
world-wide use. An on/off switch can be added
at request. All models meet CISPR 11 and FCC
class B emission limits, and are designed for
medical applications.
110 WATT MEDICAL POWER ADAPTERS
TMP110 SERIES
(MDD)
F E AT U R E S
‧ Dual, triple or quadruple outputs
‧ Optional output connectors
‧ Optional on/off switch
‧ Optional Power Fail Detect (PFD) signal
‧ 100% burn-in
‧ Wide input range 85 to 264 VAC
‧ Input surge current protection
‧ Overvoltage protection
‧ Overcurrent protection
Safety Standard Approvals：
UL 2601-1
CSA C22.2 No. 601.1
TÜV EN60601-1
INPUT SPECIFICATIONS
Input voltage： 85 to 264 VAC
Input frequency： 47 to 63 Hz
Input current： 3.20A (rms) for 115 VAC
1.80A (rms) for 230VAC
Leakage current： 90µA max. @ 115VAC, 60Hz
150µA max. @ 230VAC, 50Hz
ENVIRONMENTAL SPECIFICATIONS
Operating temperature： 0ºC to +70ºC
Storage temperature：
-40ºC to +85ºC
Relative humidity：
Derating：
5% to 95% non-condensing
Derate from 100% at +50ºC
linearly to 50% at +70ºC
OUTPUT SPECIFICATIONS
Output voltage/current： See rating chart
Total output power：
110 watts maximum
Ripple and noise：
Overvoltage protection：
1% peak to peak maximum
Provided on output #1 only;
set at 112-132% of its nominal
output voltage
Overcurrent protection： All outputs protected to short
circuit conditions
Temperature coefficient： All outputs ±0.04%/ºC
maximum
Transient response：
Maximum excursion of 4% or
better on all models,
recovering to 1% of final
value within 500us after a
25% step load change
PFD signal (optional):
TTL logic high for normal
operation and TTL logic low
upon loss of input power. This
signal appears at least 1ms
prior to +5V output dropping
5% below its nominal value.
This signal also provides a
minimum delay of 100ms after
+5V is within regulation.
GENERAL SPECIFICATIONS
Switching frequency： 20KHz to 250KHz, varies with load and line
Efficiency：
Hold-up time：
Line regulation：
70% minimum on single output models with
Vo ≥12V, 65% minimum on the others
12 msec minimum at 110VAC
±0.5% maximum at full load
Inrush current：
15 amps @ 115VAC, or 30 amps
@230VAC, at 25ºC cold start
Withstand voltage： 4000VAC from input to output 1500VAC
from input to ground
500VAC from output to ground
MTBF：
550,000 hours minimum at full load at 25ºC
ambient, calculated per MIL-HDBK-217F,
excluding DC fan.
EMC Performance (EN60601-1-2: 2001)
EN55011:
Class B conducted, Class B radiated
FCC:
Class B conducted, Class B radiated
VCCI:
Class B conducted, Class B radiated
EN61000-3-2:
Harmonic distortion, Class A
EN61000-3-3:
Line flicker
EN61000-4-2:
ESD, ±8KV air and ±6KV contact
EN61000-4-3:
Radiated immunity, 3V/m for 80~2500MHz
EN61000-4-4:
Fast transient/burst, ±2KV
EN61000-4-5:
Surge, ±1KV diff, ±2KV com.
EN61000-4-6:
Conducted immunity, 3Vrms
EN61000-4-8:
Magnetic field immunity, 3A/m
EN61000-4-11:
Voltage dips, 30% reduction for 500ms, 60%
reduction for 100ms and >95% reduction for
10ms
Tumbler Technologies + TRUMPower
3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA
Phone: [phone] ● Fax: [phone] ● email: [e-mail] ● Website: www.TRUMPower.com