WJA1030 Datasheet, PDF (1/4 Pages) TriQuint Semiconductor – +5V Active-Bias InGaP HBT Gain Block

WJA1030
+5V Active-Bias InGaP HBT Gain Block
Product Features
Product Description
Functional Diagram
• Cascadable gain block
• 50 – 4000 MHz
• 15 dB Gain @ 1.9GHz
The WJA1030 is a cascadable gain block that offers high
linearity in a low-cost surface-mount package. At 1.9 GHz,
the WJA1030 typically provides 15 dB gain, +37 dBm
OIP3, and +18 dBm P1dB. The device is housed in a
• +18 dBm P1dB @ 1.9GHz
• +37 dBm OIP3 @ 1.9GHz
RoHS-compliant SOT-89 industry-standard SMT package
using a NiPdAu plating to eliminate the possibility of tin
whiskering.
• Operates from +5V @ 80mA
• 0.2dB gain flatness from 0.3-2.5GHz ^{The WJA1030 consists of Darlington pair amplifiers using}
a high reliability InGaP/GaAs HBT process technology.
• Robust 1000V ESD, Class 1C _{The MMIC amplifier is internally matched to 50Ω and only}
• RoHS-compliant SOT-89 package ^{requires DC-blocking capacitors and a bias inductor for}
operation. An internal active bias is designed to enable
stable performance over temperature. A dropping bias
Applications
resistor is not required allowing the device to be biased
directly from a +5V supply voltage.
• Wireless Infrastructure
• General Purpose
• Cellular GSM, PCS, UMTS
The broadband amplifier can be directly applied to various
current and next generation wireless technologies such as
GSM, CDMA, W-CDMA, WiBro, and WiMAX. The
• W-CDMA, TD-SCDMA, WiMAX ^{WJA1030 is ideal for general purpose applications such as}
LO buffering, IF amplification and pre-driver stages within
the 50 to 4000 MHz frequency range.
GND
4
1
RF IN
2
GND
3
RF OUT
Function
Input
Output/Bias
Ground
Pin No.
1
3
2, 4
Specifications ⁽¹⁾
Parameter
Operational Bandwidth
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output P1dB
Output IP3 ⁽²⁾
Output IP2
Noise Figure
Device Voltage
Device Current
Units
MHz
MHz
dB
dB
dB
dBm
dBm
dBm
dB
V
mA
Min
50
Typ
1900
14.9
12
16
+18.3
+37
+44
6.1
5
80
Max
4000
1. Test conditions: 25 ºC, Supply Voltage = +5 V, 50 Ω System.. S-parameters and 3OIP measured at
device pins. All other specifications measured on evaluation board.
2. 3OIP measured with two tones at an output power of 3 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
Typical Performance ⁽³⁾
Parameter
Frequency
S21
S11
S22
Output P1dB
Output IP3 ⁽²⁾
Output IP2
Noise Figure
Units
MHz
dB
dB
dB
dBm
dBm
dBm
dB
500
14.4
-13
-16
+19.4
+37.9
+49.4
5.3
Typical
900 1900 2140
14.4 14.4 14.4
-15 -30 -36
-19 -13 -12
+19.3 +18.3 +17.5
+37 +36.6 +36.3
+48.3 +44 +41.4
5.5 6.1 6.3
2500
14.3
-33
-13
+16
+33.9
+39.2
6.5
3. Listed typical performance parameters measured on evaluation board.
Absolute Maximum Rating
Parameter
Storage Temperature
Supply Voltage
Input Power
θ_jc (junction to paddle)
Maximum Junction Temperature
Rating
-55 to +150 °C
+6.5 V
+24 dBm
80.6 °C / W
150 °C
Ordering Information
Part No.
WJA1030
WJA1030-PCB
Description
+5V Active Bias InGaP HBT Gain Block
(lead-free/green/RoHS-compliant SOT-89 Package)
50 – 4000 MHz Fully Assembled Eval. Board
Operation of this device above any of these parameters may cause permanent damage.
Standard tape / reel size = 1000 pieces on a 7″ reel
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: [phone] • e-mail: [e-mail] • Web site: www.wj.com, www.TriQuint.com
Page 1 of 4 Dec 2007