|
TPD1030F_07 Datasheet, PDF (4/6 Pages) Toshiba Semiconductor – 2-IN-1 Low-Side Switch for Motor, Solenoid and Lamp Drive | |||
|
◁ |
Thermal Characteristics
TPD1030F
Characteristics
Symbol
Max Unit
Thermal resistance, channel to
ambient (t = 10 s)
(Note3)
Rth (ch-a)
62.5 °C/W
Note 3: Drive operation: Mounted on glass epoxy board [25.4mm à 25.4mm à 0.8mm]
(with the two devices operating)
Note 4: Active clamp capability (single pulse) test condition
VDD = 25 V, Starting Tch = 25°C, L = 10 mH, IAR = 1 A, RG = 25 Ω
Note 5: Repetitive rating, pulse width limited by maximum channel temperature.
Electrical Characteristics
Characteristics
Symbol
Test
Circuit
Test Condition
Min Typ. Max Unit
Drain-source clamp voltage
V (CL) DSS
â¯
Tch=-40ï½110â
VIN = 0 V,
ID=1mA
40
â¯
60
V
Input threshold voltage
Protective circuit operation
input voltage range
Drain cut-off current
Input current
Vth
VIN (opr)
IDSS
IIN (1)
IIN (2)
â¯
Tch=25â
VDS = 13 V,
Tch=-40ï½110â ID=10mA
Tch=25â
â¯
â¯
Tch=-40ï½110â
â¯
Tch=25â
â¯
VIN = 0 V, VDS=30V
Tch=-40ï½110â
⯠Tch=25â
VIN = 5 V, at normal
operation
VIN = 5 V, when
⯠Tch=-40ï½110â overcurrent protective
circuit is actuated
1.0 ⯠2.8
V
0.9 ⯠3.0
3
â¯
7
V
3.5 â¯
7
â¯
â¯
10
μA
â¯
⯠100
â¯
⯠300
μA
â¯
⯠350
Drain-source on resistance
RDS (ON)
Tch=25â
â¯
VIN = 5 V,
Tch=-40ï½110â ID = 0.5 A
⯠0.44 0.6
Ω
â¯
⯠0.9
Overtemperature protection
TS
â¯
â¯
VIN = 5 V
150 160 â¯
°C
Overcurrent protection
Tch=25â
IS
â¯
VIN = 5 V
Tch=-40ï½110â
1
1.8 â¯
A
0.7
â¯
â¯
Switching time
tON
tOFF
Tch=25â
â¯
â¯
30
1
Tch=-40ï½110â VDD = 13 V, VIN = 0V/5 V,
Tch=25â
ID = 0.5 A
â¯
â¯
â¯
â¯
60
60
μs
Tch=-40ï½110â
â¯
â¯
90
Source-drain diode forward
voltage
VDSF
⯠Tch=25â
IF = 1 A, VIN = 0 V
â¯
⯠1.7
V
Test Circuit 1
Switching time measuring circuit
Test Circuit
TPD1030F
IN OUT GND
To be set so that
ID = 0.5 A.
V
Measured Waveforms
VIN Waveform
VOUT Waveform
90%
10%
90%
10%
tON
tOFF
4
5V
13 V
2006-10-31
|
▷ |