|
TLP3083 Datasheet, PDF (4/19 Pages) Toshiba Semiconductor – Photocouplers GaAs Infrared LED and Photo Triac | |||
|
◁ |
TLP3083,TLP3083F
7. Absolute Maximum Ratings (Note) (Unless otherwise specified, Ta = 25 î)
Characteristics
Symbol
Note
Rating
Unit
LED Input forward current
IF
50
mA
Input forward current derating
(Ta ⥠53 î)
âIF/âTa
-0.7
mA/î
Input forward current (pulsed)
IFP
(Note 1)
1
A
Input reverse voltage
VR
5
V
Junction temperature
Tj
125
î
Input power dissipation
PD
100
mW
Input power dissipation derating (Ta ⥠25 î)
âPD/âTa
-1.0
mW/î
Detector Off-state output terminal voltage
VDRM
800
V
R.M.S. on-state current
(Ta = 25 î)
IT(RMS)
100
mA
(Ta = 70 î)
50
mA
R.M.S. on-state current derating
(Ta ⥠25 î)
âIT(RMS)/âTa
-1.1
mA/î
ON-state current (pulsed)
IONP
(Note 2)
2
A
Peak non-repetitive surge current
ITSM
(Note 3)
1.2
A
Junction temperature
Tj
125
î
Output power dissipation
PO
300
mW
Output power dissipation derating (Ta ⥠25 î)
âPO/âTa
-4.0
mW/î
Common Total power dissipation
PT
400
mW
Total power dissipation derating (Ta ⥠25 î)
âPT/âTa
-4.4
mW/î
Operating temperature
Topr
-40 to 100
î
Storage temperature
Tstg
-55 to 125
î
Lead soldering temperature
(10 s)
Tsol
260
î
Isolation voltage
AC, 60 s, R.H. ⤠60 %
BVS
(Note 4)
5000
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width (PW) ⤠100 µs, 100 pps
Note 2: Pulse width (PW) ⤠100 µs, 120 pps
Note 3: Pulse width (PW) ⤠10 ms
Note 4: This device is considered as a two-terminal device: Pins 1, 2 and 3 are shorted together, and pins 4 and 6 are
shorted together.
8. Recommended Operating Conditions (Note)
Characteristics
Symbol
Note
Min Typ. Max Unit
AC mains voltage
VAC
(Note 1)
î¥
î¥
480
V
Input forward current
IF
7.5
10
20
mA
ON-state current (pulsed)
IONP
î¥
î¥
1
A
Operating temperature
Topr
-25
î¥
85
î
Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this datasheet should also be considered.
Note 1: AC use only.
©2016 Toshiba Corporation
4
2016-02-03
Rev.5.0
|
▷ |