TLP2361 Datasheet, PDF (3/16 Pages) Toshiba Semiconductor – Inverter logic type (Totem pole output)

TLP2361
7. Absolute Maximum Ratings (Note) (Unless otherwise specified, T_a = 25 )
Characteristics
Symbol Note
Rating
Unit
LED Input forward current
I_F
10
mA
Input forward current derating
(T_a ≥ 110 )
∆I_F/∆T_a
-0.13
mA/
Input forward current (pulsed)
I_FP
(Note 1)
40
mA
Input forward current derating (pulsed)
(T_a ≥ 110 )
∆I_FP/∆T_a
-1.0
mA/
Peak transient input forward current
I_FPT (Note 2)
1
A
Peak transient input forward current
derating
(T_a ≥ 110 )
∆I_FPT/∆T_a
-25
mA/
Input power dissipation
P_D
20
mW
Input power dissipation derating
(T_a ≥ 110 )
∆P_D/∆T_a
-0.5
mW/
Input reverse voltage
V_R
5
V
Detector Output current
I_O
10
mA
Output voltage
V_O
6
V
Supply voltage
V_CC
6
Output power dissipation
P_O
20
mW
Output power dissipation derating
(T_a ≥ 110 )
∆P_O/∆T_a
-0.5
mW/
Common Operating temperature
T_opr
-40 to 125

Storage temperature
T_stg
-55 to 125
Lead soldering temperature
(10 s)
T_sol
260
Isolation voltage
AC, 60 s., R.H. ≤ 60 % BV_S (Note 3)
3750
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width (PW) ≤ 1 ms, duty = 50 %
Note 2: Pulse width (PW) ≤ 1 µs, 300 pps
Note 3: This device is considered as a two-terminal device: Pins 1 and 3 are shorted together, and pins 4, 5 and 6 are
shorted together.
8. Recommended Operating Conditions (Note)
Characteristics
Symbol
Note
Min Typ. Max Unit
Input on-state current
I_F(ON)
(Note 1)
2

6
mA
Input off-state voltage
V_F(OFF)
0

0.8
V
Supply voltage
V_CC
(Note 2)
2.7 3.3/5.0 5.5
Operating temperature
T_opr
(Note 2)
-40

125

Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this datasheet should also be considered.
Note: A ceramic capacitor (0.1 µF) should be connected between pin 6 and pin 4 to stabilize the operation of a high-
gain linear amplifier. Otherwise, this photocoupler may not switch properly. The bypass capacitor should be
placed within 1 cm of each pin.
Note 1: The rise and fall times of the input on-current should be less than 0.5 µs.
Note 2: Denotes the operating range, not the recommended operating condition.
©2015 Toshiba Corporation
3
2015-11-02
Rev.5.0