TLP152 Datasheet, PDF (3/10 Pages) Toshiba Semiconductor – Photocouplers GaA As Infrared LED & Photo IC

TLP152
7. Absolute Maximum Ratings (Note) (Unless otherwise specified, T_a = 25)
Characteristics
Symbol Note
Rating
Unit
LED Input forward current
I_F
20
mA
Peak transient input forward
current
I_FPT
(Note 1)
1
A
Input reverse voltage
V_R
5
V
Input power dissipation
P_D
40
mW
Detector Peak high-level output current
(T_a = -40 to 100)
I_OPH
(Note 2)
-2.5
A
Peak low-level output current
(T_a = -40 to 100)
I_OPL
(Note 2)
+2.5
Output voltage
V_O
35
V
Supply voltage
V_CC
35
Output power dissipation
P_O
260
mW
Common Operating temperature
T_opr
-40 to 100

Storage temperature
T_stg
-55 to 125
Lead soldering temperature
(10 s)
T_sol
(Note 3)
260
Isolation voltage
AC, 1 min,
R.H. ≤ 60%, T_a = 25
BV_S
(Note 4)
3750
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width (PW) ≤ 1 µs, 300 pps
Note 2: Exponential waveform. Pulse width ≤ 0.2 µs, f ≤ 15 kHz, VCC = 20V, Ta = -40 to 100 
Exponential waveform. Pulse width ≤ 0.08 µs, f ≤ 25 kHz, VCC = 15V, Ta = -40 to 100 
Note 3: ≥ 2 mm below seating plane.
Note 4: This device is considered as a two-terminal device: Pins 1, and 3 are shorted together, and pins 4, 5 and 6
are shorted together.
8. Recommended Operating Conditions (Note)
Characteristics
Symbol Note Min Typ. Max Unit
Input on-state current
Input off-state voltage
Peak high-level output current
Peak low-level output current
Operating frequency
I_F(ON) (Note 1) 10
V_F(OFF)
0
I_OPH

I_OPL

f
(Note 2) 

15
mA

0.8
V

-2.0
A
 +2.0

250 kHz
Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this datasheet should also be considered.
Note: A ceramic capacitor (0.1 µF) should be connected between pin 6 and pin 4 to stabilize the operation of a high-
gain linear amplifier. Otherwise, this photocoupler may not switch properly. The bypass capacitor should be
placed within 1 cm of each pin.
Note 1: The rise and fall times of the input on-current should be less than 0.5 µs.
Note 2: Exponential waveform. I_OPH ≥ -0.65 A (≤ 80 ns), I_OPL ≤ 0.65 A (≤ 80 ns), T_a = 100, V_CC = 20V
3
2012-09-14
Rev.3.0