ADS8324_15 Datasheet, PDF (7/19 Pages) Texas Instruments – 14-Bit, High Speed, 1.8V MicroPower Sampling ANALOG-TO-DIGITAL CONVERTER

THEORY OF OPERATION
The ADS8324 is a classic Successive Approximation Reg-
ister (SAR) A/D converter. The architecture is based on
capacitive redistribution that inherently includes a sample-
and-hold function. The converter is fabricated on a 0.6μ
CMOS process. The architecture and process allow the
ADS8324 to acquire and convert an analog signal at up to
50,000 conversions per second while consuming less than
3.0mW from +V_CC.
The ADS8324 requires an external reference, an external
clock, and a single power source (V_CC). The external refer-
ence can be any voltage between 500mV and V_CC /2. The
value of the reference voltage directly sets the range of the
analog input. The reference input current depends on the
conversion rate of the ADS8324.
The external clock can vary between 24kHz (1kHz through-
put) and 1.2MHz (50kHz throughput). The duty cycle of the
clock is essentially unimportant as long as the minimum
high and low times are at least 200ns. The minimum clock
frequency is set by the leakage on the capacitors internal to
the ADS8324.
The analog input is provided to two input pins: +In and –In.
When a conversion is initiated, the differential input on these
pins is sampled on the internal capacitor array. While a
conversion is in progress, both inputs are disconnected from
any internal function.
The digital result of the conversion is clocked out by the
DCLOCK input and is provided serially, most significant bit
first, on the D_OUT pin. The digital data that is provided on the
D_OUT pin is for the conversion currently in progress—there
is no pipeline delay. It is possible to continue to clock the
ADS8324 after the conversion is complete and to obtain the
serial data least significant bit first. See the digital timing
section for more information.
2 • V_REF
peak-to-peak
Common
Voltage
ADS8324
Single-Ended Input
Common
Voltage
V_REF
peak-to-peak
V_REF
peak-to-peak
ADS8324
Differential Input
FIGURE 1. Methods of Driving the ADS8324—Single-Ended
or Differential.
2
1.8
V_CC = 1.8V
1.6
1.4
1.2
1
0.8
Single-Ended Input
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1
0.5
0.6
0.7
0.8
V_REF (V)
0.9
1
ANALOG INPUT
The analog input is bipolar and fully differential. There are
two general methods of driving the analog input of the
ADS8324: single-ended or differential, as shown in Figure
1. When the input is single-ended, the –In input is held at a
fixed voltage. The +In input swings around the same voltage
and the peak-to-peak amplitude is 2 • V_REF. The value of
V_REF determines the range over which the common voltage
may vary, as shown in Figure 2.
When the input is differential, the amplitude of the input is
the difference between the +In and –In input, or, +In – (–In).
A voltage or signal is common to both of these inputs. The
peak-to-peak amplitude of each input is V_REF about this
common voltage. However, since the inputs are 180° out-of-
phase, the peak-to-peak amplitude of the difference voltage
is 2 • V_REF. The value of V_REF also determines the range of
the voltage that may be common to both inputs, as shown in
Figure 3.
In each case, care should be taken to ensure that the output
impedance of the sources driving the +In and –In inputs are
matched. If this is not observed, the two inputs could have
FIGURE 2. Single-Ended Input—Common Voltage Range
vs V_REF.
2
1.8
1.6
1.4
Differential Input
1.2
1
0.8
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1
V_CC = 1.8V
0.5
0.6
0.7
0.8
V_REF (V)
0.9
1
FIGURE 3. Differential Input—Common Voltage Range vs
V_REF.
ADS8324
7
SBAS172A
www.ti.com