ADC0831-N Datasheet, PDF (7/35 Pages) Texas Instruments – ADC0831/ADC0832/ADC0834/ADC0838 8-Bit Serial I/O A/D Converters with Multiplexer Options

AC Characteristics
The following specifications apply for V_CC = 5V, t_r = t_f = 20 ns and 25˚C unless otherwise specified.
Typ
Tested
Parameter
Conditions
(Note 12)
Limit
(Note 13)
f_CLK, Clock Frequency
Min
10
Max
t_C, Conversion Time
Not including MUX Addressing Time
8
Clock Duty Cycle
Min
(Note 10)
Max
t_SET-UP, CS Falling Edge or
Data Input Valid to CLK
Rising Edge
t_HOLD, Data Input Valid
after CLK Rising Edge
t_pd1, t_pd0 — CLK Falling
C_L=100 pF
Edge to Output Data Valid
Data MSB First
650
(Note 11)
Data LSB First
250
t_1H, t_0H, — Rising Edge of
CS to Data Output and
C_L=10 pF, R_L=10k
125
(see TRI-STATE^® Test Circuits)
SARS Hi–Z
C_IN, Capacitance of Logic
Input
C_L=100 pf, R_L=2k
500
5
C_OUT, Capacitance of Logic
5
Outputs
Design
Limit
(Note 14)
400
40
60
250
90
1500
600
250
Limit
Units
kHz
kHz
1/f_CLK
%
%
ns
ns
ns
ns
ns
ns
pF
pF
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its specified operating conditions.
Note 2: All voltages are measured with respect to the ground plugs.
Note 3: Internal zener diodes (6.3 to 8.5V) are connected from V+ to GND and V_CC to GND. The zener at V+ can operate as a shunt regulator and is connected
to V_CC via a conventional diode. Since the zener voltage equals the A/D’s breakdown voltage, the diode insures that V_CC will be below breakdown when the device
is powered from V+. Functionality is therefore guaranteed for V+ operation even though the resultant voltage at V_CC may exceed the specified Absolute Max of 6.5V.
It is recommended that a resistor be used to limit the max current into V+. (See Figure 3 in Functional Description Section 6.0)
Note 4: When the input voltage (V_IN) at any pin exceeds the power supply rails (V_IN < V^− or V_IN > V⁺) the absolute value of current at that pin should be limited
to 5 mA or less. The 20 mA package input current limits the number of pins that can exceed the power supply boundaries with a 5 mA current limit to four.
Note 5: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 6: Total unadjusted error includes offset, full-scale, linearity, and multiplexer errors.
Note 7: Cannot be tested for ADC0832.
Note 8: For V_IN(−)≥V_IN(+) the digital output code will be 0000 0000. Two on-chip diodes are tied to each analog input (see Block Diagram) which will forward conduct
for analog input voltages one diode drop below ground or one diode drop greater than the V_CC supply. Be careful, during testing at low V_CC levels (4.5V), as high
level analog inputs (5V) can cause this input diode to conduct — especially at elevated temperatures, and cause errors for analog inputs near full-scale. The spec
allows 50 mV forward bias of either diode. This means that as long as the analog V_IN or V_REF does not exceed the supply voltage by more than 50 mV, the output
code will be correct. To achieve an absolute 0 V_DC to 5 V_DC input voltage range will therefore require a minimum supply voltage of 4.950 V_DC over temperature
variations, initial tolerance and loading.
Note 9: Leakage current is measured with the clock not switching.
Note 10: A 40% to 60% clock duty cycle range insures proper operation at all clock frequencies. In the case that an available clock has a duty cycle outside of these
limits, the minimum, time the clock is high or the minimum time the clock is low must be at least 1 µs. The maximum time the clock can be high is 60 µs. The clock
can be stopped when low so long as the analog input voltage remains stable.
Note 11: Since data, MSB first, is the output of the comparator used in the successive approximation loop, an additional delay is built in (see Block Diagram) to allow
for comparator response time.
Note 12: Typicals are at 25˚C and represent most likely parametric norm.
Note 13: Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 14: Guaranteed but not 100% production tested. These limits are not used to calculate outgoing quality levels.
www.national.com
6