5962R8771003VXA Datasheet, PDF (7/30 Pages) Texas Instruments – LM158QML Low Power Dual Operational Amplifiers

LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
SMD 5962–8771002, High Dose Rate
DC Drift Parameters
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Delta calculations are performed on QMLV devices at Group B, Subgroup 5 only.
Parameter
Test Conditions
Notes Min Max Units
Sub-
groups
V_IO
Input Offset Voltage
±I_IB
Input Bias Current
+V_CC = 30V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, V_CM = 28.5V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 5V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 5V, V_CM = 0V
-0.5 0.5
mV
1
-0.5 0.5
mV
1
-0.5 0.5
mV
1
See⁽¹⁾ -10 10
nA
1
(1) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
SMD 5962–8771002, High Dose Rate SMD 5962–8771002, High Dose Rate
100K Post Radiation Limits @ +25°C⁽¹⁾
DC Parameters
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Parameter
Test Conditions
V_IO
Input Offset Voltage
+V_CC = 30V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, V_CM = 28.5V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 5V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
±I_IB
Input Bias Current
+V_CC = 5V, V_CM = 0V
I_CC
Power Supply Current
+V_CC = 5V, R_L = 100K,
V_O = 1.4V
Notes Min Max
See⁽¹⁾ -4.0 4.0
See⁽¹⁾ -4.0 4.0
See⁽¹⁾ -4.0 4.0
See ^{(1) (2)}
See ⁽¹⁾
-60 -1.0
1.5
Units
mV
mV
mV
nA
mA
Sub -
groups
1
1
1
1
1
(1) Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post
Radiation Limits Table. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate
sensitivity. Radiation end point limits for the noted parameters are specified only for the conditions as specified in MIL-STD-883, per
Test Method 1019, Condition A.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
LM158A Electrical Characteristics SMD 5962–8771003 ELDRS Free Only
DC Parameters
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Parameter
Test Conditions
Notes Min Max
I_CC
Power Supply Current
V_OH
Output Voltage High
V_OL
Output Voltage Low
+V_CC = 5V, R_L = 100K,
V_O = 1.4V
+V_CC = 30V, R_L = 100K,
V_O = 1.4V
+V_CC = 30V, R_L = 2KΩ
+V_CC = 30V, R_L = 10KΩ
+V_CC = 30V, R_L = 10KΩ
+V_CC = 30V, I_Sink = 1µA
+V_CC = 5V, R_L = 10KΩ
1.2
3.0
4.0
26
27
40
100
40
100
40
100
Units
mA
mA
V
V
mV
mV
mV
mV
mV
mV
Sub-
groups
1, 2, 3
1,
2, 3
1, 2, 3
1, 2, 3
1
2, 3
1
2, 3
1
2, 3
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
Submit Documentation Feedback
7