GD75323_16 Datasheet, PDF (5/19 Pages) Texas Instruments – MULTIPLE RS-232 DRIVERS AND RECEIVERS

GD75323
MULTIPLE RS-232 DRIVERS AND RECEIVERS
DRIVER SECTION
SLLS213A – JANUARY 1996 – REVISED JUNE 1999
electrical characteristics over operating free-air temperature range, V_DD = 9 V, V_SS = –9 V,
V_CC = 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNIT
VOH
VOL
IIH
IIL
IOS(H)
High-level output voltage
Low-level output voltage (see Note 3)
High-level input current
Low-level input current
High-level short-circuit output current
(see Note 4)
VIL = 0.8 V,
VIH = 1.9 V,
VI = 5 V,
VI = 0,
VIL = 0.8 V,
RL = 3 kΩ,
RL = 3 kΩ,
See Figure 2
See Figure 2
See Figure 1
See Figure 1
VO = 0,
See Figure 1
6 7.5
V
– 7.5 – 6 V
10 µA
– 1.6 mA
– 4.5 – 9 – 19.5 mA
IOS(L) Low-level short-circuit output current VIH = 2 V,
VO = 0,
See Figure 1
4.5
9
19 mA
ro
Output resistance (see Note 5)
VCC = VDD = VSS = 0,
VO = – 2 V to 2 V 300
Ω
NOTES:
3. The algebraic convention, where the more positive (less negative) limit is designated as maximum, is used in this data sheet for logic
levels only, e.g., if – 10 V is maximum, the typical value is a more negative voltage.
4. Output short-circuit conditions must maintain the total power dissipation below absolute maximum ratings.
5. Test conditions are those specified by TIA/EIA-232-F and as listed above.
switching characteristics, V_DD = 12 V, V_SS = –12 V, V_CC = 5 V ±10%, T_A = 25°C
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNIT
tPLH
tPHL
tTLH
Propagation delay time, low- to high-level output
Propagation delay time, high- to low-level output
Transition time, low- to high-level output
RL = 3 kΩ to 7 kΩ,
See Figure 3
RL = 3 kΩ to 7 kΩ,
See Figure 3
RL = 3 kΩ to 7 kΩ,
See Figure 3 and Note 6
CL = 15 pF,
CL = 15 pF,
CL = 2500 pF,
315 500 ns
75 175 ns
60 100 ns
1.7 2.5 µs
Transition time, high- to low-level output (see
tTHL _{Note 5)}
RL = 3 kΩ to 7 kΩ,
See Figure 3
RL = 3 kΩ to 7 kΩ,
See Figure 3 and Note 7
CL = 15 pF,
CL = 2500 pF,
40
75 ns
1.5 2.5 µs
NOTES:
6. Measured between – 3-V and 3-V points of the output waveform (TIA/EIA-232-F conditions), all unused inputs are tied either high
or low.
7. Measured between 3-V and – 3-V points of the output waveform (TIA/EIA-232-F conditions), all unused inputs are tied either high
or low.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
5