BQ27505 Datasheet, PDF (5/42 Pages) Texas Instruments – System-Side Impedance Track™ Fuel Gauge

Not Recommended for New Designs
bq27505
www.ti.com
3 ELECTRICAL SPECIFICATIONS
SLUS884 – FEBRUARY 2009
3.1 ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)⁽¹⁾
PARAMETER
VALUE
UNIT
V_CC
V_IOD
V_BAT
V_I
ESD
Supply voltage range
Open-drain I/O pins (SDA, SCL, SOC_INT)
BAT input pin
Input voltage range to all other pins (BI/Tout, TS, SRP, SRN, BAT_GD)
Human-body model (HBM), BAT pin
Human-body model (HBM), all other pins
–0.3 to 2.75
V
–0.3 to 6
V
–0.3 to 6
–0.3 to V_CC + 0.3
V
1.5
kV
2
T_A
Operating free-air temperature range
T_F
Functional temperature range
T_stg
Storage temperature range
–40 to 85
°C
–40 to 100
°C
–65 to 150
°C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
3.2 RECOMMENDED OPERATING CONDITIONS
T_A = -40°C to 85°C; 2.4 V < V_CC < 2.6 V; Typical values at T_A = 25°C and V_CC = 2.5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNIT
V_CC
I_CC
I_SLP+
I_SLP
I_HIB
V_OL
Supply voltage
Normal operating-mode current⁽¹⁾
Sleep+ operating mode current⁽¹⁾
Low-power storage-mode current⁽¹⁾
Hibernate operating-mode current⁽¹⁾
Output voltage, low (SCL, SDA, SOC_INT,
BAT_LOW)
Fuel gauge in NORMAL mode.
I_LOAD > Sleep Current
Fuel gauge in SLEEP+ mode.
I_LOAD < Sleep Current
Fuel gauge in SLEEP mode.
I_LOAD < Sleep Current
Fuel gauge in HIBERNATE mode.
I_LOAD < Hibernate Current
I_OL = 3 mA
2.4 2.5
114
58
19
4
2.6 V
mA
mA
mA
mA
0.4 V
V_OH(PP)
V_OH(OD)
V_IL
V_IH(OD)
Output voltage, high (BAT_LOW, BAT_GD)
Output voltage, high (SDA, SCL, SOC_INT)
Input voltage, low (SDA, SCL)
Input voltage, low (BI/TOUT)
Input voltage, high (SDA, SCL)
Input voltage, high (BI/TOUT)
I_OH = –1 mA
External pullup resistor connected to
V_CC
BAT INSERT CHECK MODE active
BAT INSERT CHECK MODE active
V_CC – 0.5
V_CC – 0.5
–0.3
–0.3
1.2
1.2
V
V
0.6
0.6
6V
V_CC +
0.3
V_A1
V_A2
V_A3
I_lkg
t_PUCD
Input voltage range (TS)
Input voltage range (BAT)
Input voltage range (SRP, SRN)
Input leakage current (I/O pins)
Power-up communication delay
V_SS – 0.125
V_SS – 0.125
V_SS – 0.125
2V
5V
0.125 V
0.3 mA
250
ms
(1) Specified by design. Not production tested.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): bq27505
ELECTRICAL SPECIFICATIONS
5