AMC1200STDUBRQ1 Datasheet, PDF (5/23 Pages) Texas Instruments – Fully Differential Isolation Amplifier

AMC1200-Q1
www.ti.com
SBAS585 – SEPTEMBER 2012
PACKAGE CHARACTERISTICS⁽¹⁾
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
L(I01) Minimum air gap (clearance)
Shortest terminal-to-terminal distance
through air
7
mm
L(I02) Minimum external tracking (creepage)
Shortest terminal-to-terminal distance
across the package surface
7
mm
CTI
Tracking resistance
(comparative tracking index)
DIN IEC 60112/VDE 0303 part 1
≥ 175
V
Minimum internal gap
(internal clearance)
Distance through the insulation
0.014
mm
R_IO Isolation resistance
C_IO Barrier capacitance input to output
C_I
Input capacitance to ground
Input to output, V_IO = 500 V, all pins on
each side of the barrier tied together to
create a two-terminal device, T_A < 85°C
Input to output, V_IO = 500 V,
85°C ≤ T_A < T_A max
V_I = 0.5 V_PP at 1 MHz
V_I = 0.5 V_PP at 1 MHz
> 10¹²
Ω
> 10¹¹
Ω
1.2
pF
3
pF
(1) Creepage and clearance requirements should be applied according to the specific equipment isolation standards of a specific
application. Care should be taken to maintain the creepage and clearance distance of the board design to ensure that the mounting
pads of the isolator on the printed circuit board (PCB) do not reduce this distance. Creepage and clearance on a PCB become equal
according to the measurement techniques shown in the Isolation Glossary section. Techniques such as inserting grooves and/or ribs on
the PCB are used to help increase these specifications.
ELECTRICAL CHARACTERISTICS
All minimum/maximum specifications at T_A = –40°C to 105°C and within the specified voltage range, unless otherwise noted.
Typical values are at T_A = 25°C, VDD1 = 5 V, and VDD2 = 3.3 V.
PARAMETER
TEST CONDITIONS
AMC1200-Q1
MIN
TYP
UNIT
MAX
INPUT
Maximum input voltage before
clipping
VINP – VINN
±320
mV
Differential input voltage
VINP – VINN
–250
250 mV
V_CM
V_OS
TCV_OS
CMRR
C_IN
C_IND
R_IN
Common-mode operating range
Input offset voltage
Input offset thermal drift
Common-mode rejection ratio
Input capacitance to GND1
Differential input capacitance
Differential input resistance
Small-signal bandwidth
V_IN from 0 V to 5 V at 0 Hz
V_IN from 0 V to 5 V at 50 kHz
VINP or VINN
–0.16
–1.5
±0.2
–10
±1.5
108
95
3
3.6
28
60
100
VDD1
1.5
10
V
mV
µV/K
dB
pF
pF
kΩ
kHz
OUTPUT
Nominal gain
8
G_ERR
Gain error
Initial, at T_A = 25°C
–0.5% ±0.05%
–1% ±0.05%
0.5%
1%
TCG_ERR Gain error thermal drift
Nonlinearity
4.5 V ≤ VDD2 ≤ 5.5 V
2.7 V ≤ VDD2 ≤ 3.6 V
±56
–0.075% ±0.015%
–0.1% ±0.023%
0.075%
0.1%
ppm/K
Nonlinearity thermal drift
2.4
ppm/K
PSRR
Output noise
Power-supply rejection ratio
VINP = VINN = 0 V
vs VDD1, 10-kHz ripple
vs VDD2, 10-kHz ripple
3.1
mV_RMS
80
dB
61
Rise/fall time
0.5-V step, 10% to 90%
3.66
6.6
µs
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: AMC1200-Q1
Submit Documentation Feedback
5