DS25CP152_14 Datasheet, PDF (4/17 Pages) Texas Instruments – DS25CP152 3.125 Gbps LVDS 2x2 Crosspoint Switch

DS25CP152
SNLS274D – JANUARY 2008 – REVISED APRIL 2013
DC Electrical Characteristics (continued)
Over recommended operating supply and temperature ranges unless otherwise specified.^{(1) (2) (3)}
Symbol
Parameter
Conditions
Min
V_CL
Input Clamp Voltage
LVDS INPUT DC SPECIFICATIONS
I_CL = −18 mA, V_CC = 0V
V_ID
V_TH
V_TL
V_CMR
Input Differential Voltage
Differential Input High Threshold
Differential Input Low Threshold
Common Mode Voltage Range
V_CM = +0.05V or V_CC-0.05V
V_ID = 100 mV
0
−100
0.05
I_IN
Input Current
C_IN
Input Capacitance
R_IN
Input Termination Resistor
LVDS OUTPUT DC SPECIFICATIONS
V_IN = +3.6V or 0V
V_CC = 3.6V or 0V
Any LVDS Input Pin to GND
Between IN+ and IN-
V_OD
ΔV_OD
Differential Output Voltage
Change in Magnitude of V_OD for Complimentary
Output States
R_L = 100Ω
V_OS
ΔV_OS
I_OS
Offset Voltage
Change in Magnitude of V_OS for Complimentary
Output States
Output Short Circuit Current ⁽⁴⁾
C_OUT Output Capacitance
R_OUT Output Termination Resistor
SUPPLY CURRENT
R_L = 100Ω
OUT to GND
OUT to V_CC
Any LVDS Output Pin to GND
Between OUT+ and OUT-
I_CC
Supply Current
I_CCZ
Supply Current with Outputs Disabled
EN0 = EN1 = High
EN0 = EN1 = Low
(4) Output short circuit current (I_OS) is specified as magnitude only, minus sign indicates direction only.
250
-35
1.05
-35
Typ
−0.9
0
0
±1
1.7
100
350
1.2
-35
7
1.2
100
64
23
www.ti.com
Max Units
−1.5
V
1
V
+100 mV
mV
V_CC -
V
0.05
±10
μA
pF
Ω
450 mV
35
mV
1.375 V
35
mV
-55
mA
55
mA
pF
Ω
77
mA
29
mA
AC Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified ^{(1) (2)}
Symbol
Parameter
Conditions
Min Typ Max Units
LVDS OUTPUT AC SPECIFICATIONS
t_PLHD
t_PHLD
Differential Propagation Delay Low to
High ⁽³⁾
Differential Propagation Delay High to
Low ⁽³⁾
R_L = 100Ω
340 500
ps
344 500
ps
t_SKD1
Pulse Skew |t_PLHD − t_PHLD|
(3) (4)
4
35
ps
t_SKD2
Channel to Channel Skew
(3) (5)
12
40
ps
t_SKD3
Part to Part Skew
(3) (6)
50
150
ps
(1) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or notes. Typical specifications are estimations only and
are not ensured.
(2) Typical values represent most likely parametric norms for V_CC = +3.3V and T_A = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Specification is ensured by characterization and is not tested in production.
(4) t_SKD1, |t_PLHD − t_PHLD|, Pulse Skew, is the magnitude difference in differential propagation delay time between the positive going edge and
the negative going edge of the same channel.
(5) t_SKD2, Channel to Channel Skew, is the difference in propagation delay (t_PLHD or t_PHLD) among all output channels in Broadcast mode
(any one input to all outputs).
(6) t_SKD3, Part to Part Skew, is defined as the difference between the minimum and maximum differential propagation delays. This
specification applies to devices at the same V_CC and within 5°C of each other within the operating temperature range.
4
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS25CP152