THS4041-Q1 Datasheet, PDF (3/23 Pages) Texas Instruments – 165-MHz C-STABLE HIGH-SPEED AMPLIFIER

ą
THS4041ĆQ1
165ĆMHz CĆSTABLE HIGHĆSPEED AMPLIFIER
recommended operating conditions
Supply voltage, VCC+ and VCC−
Operating free-air temperature, TA
Dual supply
Single supply
I-suffix
SGLS229B − FEBRUARY 2004 − REVISED JUNE 2008
MIN
±4.5
9
−40
NOM
MAX
±16
32
85
UNIT
V
°C
electrical characteristics at T_A = 25°C, V_CC = ±15 V, R_L = 150 Ω (unless otherwise noted)
dynamic performance
PARAMETER
TEST CONDITIONS†
VCC = ±15 V
Dynamic performance small-signal bandwidth ^{VCC = ±5 V}
(−3 dB)
VCC = ±15 V
BW
Bandwidth for 0.1 dB flatness
VCC = ±5 V
VCC = ±15 V
VCC = ±5 V
Full power bandwidth§
VO(pp) = 20 V,
VO(pp) = 5 V,
SR Slew rate‡
VCC = ±15 V,
VCC = ±5 V,
Settling time to 0.1%
ts
Settling time to 0.01%
VCC = ±15 V,
VCC = ±5 V,
VCC = ±15 V,
VCC = ±5 V,
† _{Full range = −40°C to 85°C for I suffix}
‡ _{Slew rate is measured from an output level range of 25% to 75%.}
§ _{Full power bandwidth = slew rate / 2 π VO(Peak).}
Rf = 200 Ω
Rf = 200 Ω
Rf = 1.3 kΩ
Rf = 1.3 kΩ
Rf = 200 Ω
Rf = 200 Ω
VCC = ±15 V
VCC = ±5 V
20-V step,
5-V step,
5-V step
2-V step
5-V step
2-V step
Gain = 1
Gain = 2
Gain = 1
Gain = 5
Gain = −1
Gain = −1
Gain = −1
noise/distortion performance
PARAMETER
TEST CONDITIONS†
THD Total harmonic distortion
Vn
Input voltage noise
In
Input current noise
VO(pp) = 2 V,
f = 1 MHz, Gain = 2
VCC = ±15 V
VCC = ±5 V
VCC = ±5 V or ±15 V, f = 10 kHz
VCC = ±5 V or ±15 V, f = 10 kHz
RL = 150 Ω
RL = 1 kΩ
RL = 150 Ω
RL = 1 kΩ
Differential gain error
Differential phase error
† _{Full range = −40°C to 85°C for I suffix}
Gain = 2,
40 IRE modulation,
Gain = 2,
40 IRE modulation,
NTSC,
±100 IRE ramp
NTSC,
±100 IRE ramp
VCC = ±15 V
VCC = ±5 V
VCC = ±15 V
VCC = ±5 V
MIN TYP MAX UNIT
165
MHz
150
60
MHz
60
45
MHz
45
6.3
MHz
20
400
V/µs
325
120
ns
120
250
ns
280
MIN TYP
−75
−89
−75
−86
14
0.9
0.01%
0.01%
0.01°
0.02°
MAX UNIT
dBc
nV/√Hz
pA/√Hz
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
3