OPA699IDG4 Datasheet, PDF (3/31 Pages) Texas Instruments – Wideband, High Gain VOLTAGE LIMITING AMPLIFIER

ELECTRICAL CHARACTERISTICS: V_S = ±5V
Boldface limits are tested at +25°C.
G = +6, R_F = 750Ω, R_L = 500Ω, and V_H = –V_L = 2V, (see Figure 1 for AC performance only), unless otherwise noted.
OPA699ID
TYP
MIN/MAX OVER TEMPERATURE
PARAMETER
CONDITIONS
+25°C
+25°C⁽¹⁾
0°C to
70°C⁽²⁾
–40°C to
+85°C⁽²⁾
MIN/ TEST
UNITS MAX LEVEL⁽³⁾
AC PERFORMANCE (see Figure 1)
Small Signal Bandwidth (V_O < 0.5V_PP)
Gain Bandwidth Product (G ≥ +20)
Gain Peaking
0.1dB Gain Flatness Bandwidth
Large-Signal Bandwidth
Step Response
Slew Rate
Rise-and-Fall Time
Settling Time: 0.05%
Spurious-Free Dynamic Range, Even
Odd
Differential Gain
Differential Phase
Input Noise Density
Voltage Noise
Current Noise
G = +6
G = +12
G = –6
V_O < 0.5V_PP, G = +6
V_O < 0.5V_PP, G = +4
V_O < 0.5V_PP
V_O = 4V_PP
4V Step
0.5V Step
2V Step
f = 5MHz, V_O = 2V_PP
f = 5MHz, V_O = 2V_PP
NTSC, PAL, R_L = 500Ω
NTSC, PAL, R_L = 500Ω
f ≥ 1MHz
f ≥ 1MHz
260
86
269
1000
7.5
30
290
1400
1.6
8
67
87
0.012
0.008
4.1
2.0
220
820
190
1300
1.65
64
85
4.6
2.5
215
800
180
1200
1.8
62
84
5.2
2.7
210
750
170
1100
2
60
80
5.5
2.9
MHz min B
MHz
typ C
MHz
typ C
MHz min B
dB
typ C
MHz
typ C
MHz min B
V/µs min B
ns
max B
ns
typ C
dB
min B
dB
min B
%
typ C
°
typ C
nV/√Hz max B
pA/√Hz max B
DC PERFORMANCE (V_CM = 0V)
Open-Loop Voltage Gain (A_OL)
Input Offset Voltage
Average Drift
Input Bias Current⁽⁴⁾
Average Drift
Input Offset Current
Average Drift
INPUT
Common-Mode Rejection Ratio
Common-Mode Input Range⁽⁵⁾
Input Impedance
Differential-Mode
Common-Mode
V_O = ±0.5V
Input Referred, V_CM = ±0.5V
66
58
56
55
dB
min A
±1.5
±5.0
±6
±7
mV max A
—
±15
±20
µV/°C max B
+3
±10
±11
±12
µA
max A
—
±15
±20
nA/°C max B
±0.3
±2
±2.5
±3
µA
max A
—
±10
±10
nA/°C max B
61
55
54
52
±3.3
±3.2
±3.2
±3.1
dB
min A
V
min A
0.32 || 1
3.5 || 1
MΩ || pF typ C
MΩ || pF typ C
OUTPUT
Output Voltage Range
Current Output, Sourcing
Sinking
Closed-Loop Output Impedance
V_H = –V_L = 4.3V
R_L ≥ 500Ω
G = +4, f < 100kHz
±4.1
±3.9
±3.9
±3.8
+120
+90
+85
+80
–120
–90
–85
–80
0.8
V
min A
mA
min A
mA
min A
Ω
typ C
POWER SUPPLY
Operating Voltage, Specified
Maximum
Quiescent Current, Maximum
Minimum
Power-Supply Rejection Ratio
+PSRR (Input Referred)
V_S = ±5V
V_S = ±5V
+V_S = 4.5V to 5.5V
±5
—
±6
±6
±6
15.5
15.9
16.3
16.6
15.5
15.2
14.9
14.6
75
68
67
66
V
typ C
V
max A
mA max A
mA
min A
dB
min A
NOTES: (1) Junction temperature = ambient temperature for low temperature limit and +25°C Test Level A specifications. Junction temperature = ambient
temperature + 23°C at high temperature limit Test Level A specifications.
(2) Junction temperature = ambient at low temperature limit; junction temperature = ambient +1°C at high temperature limit for over-temperature
tested specifications.
(3) Test Levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value for information only.
(4) Current is considered positive out-of-node.
(5) CMIR tested as < 3dB degradation from minimum CMRR at specified limits.
(6) I_VH (V_H bias current) is positive, and I_VL (V_L bias current) is negative, under these conditions. See Note 3 and Figures 1 and 12.
(7) Limiter feedthrough is the ratio of the output magnitude to the sinewave added to V_H (or V_L) when V_IN = 0.
OPA699
3
SBOS261D
www.ti.com